Philips 26MD350B/F7 owner manual TV Functions,  Initial Setup, Before you begin

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

TV Functions

INTRODUCTION

Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and autoprogram, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cable.

1 After making all the necessary connections, press [y(power)] to turn on the unit.

• This operation may take a few moments.

2 Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI iti l Setupt

Select the language for setup display.
			English
Elija el idioma de ajuste.
			Español
Sélectionner langue écran config.			Français
Select	OK OK	MENU
			Skip

•“Initial Setup” menu on step 3 will be displayed in the selected language after you press [OK].

3 Use [Cursor K/L] to select “Antenna” for TV channels or “Cable” for CATV channels, then press [OK].

InitialI iti l Setupt

Make sure the antenna is connected to ''ANT. IN'' jack.			Antenna
Select your signal source.
			Cable
			Skip
	Antenna
	Cable	Or
			ANT.IN
Select	OK OK	BACK	MENU
		Back	Skip

• “Autoprogram” will begin.

InitialI iti l Setupt

Now the system is scanning for channels, please wait.

Auto programming will take up to 20 minutes to complete.

0%

Analog channels	0ch
Digital channels	0ch

MENU

Skip

	PREPARATION
InitialI iti l Setupt
4 Use [Cursor s/ B] to select the desired location setting,
then press [OK].

Select “Retail” or “Home” for your location.

						WATCHING
		Retail			H o m e
		Select			OK OK
• Select ”Retail” store, the unit will be set up with						TV
predefined setting for retail displays. In this setting,
the power consumption may possibly exceed
• Select ”Home”, the unit is set to maximize the energy						OPTIONAL
the limited requirement of the ENERGY STAR®
qualification.
efficiency for home setting and it can be adjusted						SETTING
according to your preference.
through a choice of picture and sound quality
• When the initial setup is completed, the lowest
						OPERATING
memorized channel with the confirmation message
of the location setting will be displayed on the TV
screen.
Note:						DVD
• If you are not receiving a signal from your cable service,
contact the Cable provider.
• If you press [y(power)] or [MENU] during autoprogram,
this setting will be canceled.						DVD
• The initial autoprogram function can be executed for
either “Antenna” or “Cable” only once. When you change						SETTING
the connection (Antenna / Cable), set autoprogram again.
Refer to page 22.
• If there is no signal input from the antenna terminal and
no operation for several seconds after you turn on the unit,
“Helpful Hints” appears. Follow the instructions listed on
the TV screen.
						TROUBLESHOOTING
	Select OK OK		Skip
	InitialI iti l Setupt
	No channel is registered.			Retry
	Try Autoprogram again?			Later
	Verify that you have a cable connected to the "ANT. IN" jack on the
	back of the TV, the channel installation process searches this
	connection. If you are using a cable or satellite box, please confirm
	the input which you have connected the box and press "SOURCE"
	key on the remote control to select the appropriate source input.
		MENU
• You must set ”Home” in step 4. Otherwise, the settings
						INFORMATION
of picture and sound quality you adjusted will not be
• If you want to scan the channels automatically again,
memorized after you turn off the unit.
After an initial setup is completed...
refer to “Autoprogram” on page 22.
• You can add the desired cable and analog channels
unmemorized by “Autoprogram”. Refer to “Add
Channels” on page 23.
• If you want to change to another language, refer to
“Language Selection” on page 24.
• If you want to change the location setting, refer to
“Location” on page 35.					17

EN