1) Measured at 100 hrs of life in vertical position.
2) Measured at rated lamp watts on a linear reactor.LPW does not include ballast losses.
3) Measured with the lamp operating at rated watts.
Electrical Data (Subject to change without notice)
Warnings, Cautions and Operating Instructions
“WARNING:These lamps can cause serious skin burn and eye inflammation
from short wave ultraviolet radiation if outer envelope of the lamp is broken or
punctured.Do not use where people will remain for more than a few minutes
unless adequate shielding or other safety precautions are used.Certain lamps
that will automatically extinguish when the outer envelope is broken or punctured
are commercially available.” This lamp complies with FDA radiation performance
standard 21 CFR subchapter J.(USA:21CFR 1040.30 Canada: SOR/DORS/80-381)
If the outer bulb is broken or punctured,turn off at once and replace
the lamp to avoid possible injury from hazardous short wave ultraviolet
radiation.Do not scratch the outer bulb or subject it to pressure as
this could cause the outer bulb to crack or shatter.A partial vacuum
in the outer bulb may cause glass to fly if the envelope is struck.
WARNING:The arc-tube of metal halide lamps are designed to operate under
high pressure and at temperatures up to 1000ºC and can unexpectedly rupture
due to internal or external factors such as a ballast failure or misapplication.If the
arc-tube ruptures for any reason,the outer bulb may break and pieces of extremely
hot glass might be discharged into the surrounding environment.If such a rupture
were to happen,THERE IS A RISK OF PERSONAL INJURY,PROPERTY
DAMAGE,BURNS AND FIRE.
Certain lamps that will retain all the glass particles should inner arc-tube rupture
occur are commercially available from Philips Lighting Company.
RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE.
Allowing lamps to operate until they fail is not advised and may
increase the possibility of inner arc tube rupture.
This lamp contains an arc tube with a filling gas containing Kr-85 and is distrib-
uted by Philips Lighting Company,a division of Philips Electronics North America
Corporation,Somerset, New Jersey 08875-6800.
CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY,PROPERTY
DAMAGE,BURNS AND FIRE RESULTING FROM AN ARC-TUBE RUPTURE
THE FOLLOWING LAMP OPERATING INSTRUCTIONS MUST BE FOLLOWED.
Lamp Operating Instructions:
1) RELAMP FIXTURES AT OR BEFORE THE END OF RATED LIFE.Allowing
lamps to operate until they fail is not advised and may increase the possibility
of inner arc tube rupture.
2) Use only in an enclosed fixture capable of withstanding particles of glass
having temperatures up to 1000ºC.
3) Before lamp installation/replacement,shut power off and allow lamp and
fixture to cool to avoid electrical shock and potential burn hazards.
4) Use only auxiliary equipment meeting Philips and/or ANSI standards.
Use within voltage limits recommended by ballast manufacturer.
A.Operate lamp only within specified limits of operation.
B. For total supply load refer to ballast manufacturers electrical data.
5) Periodically inspect the outer envelope.Replace any lamps that show
scratches,cracks or damage.
6)If a lamp bulb support is used, be sure to insulate the support electrically
to avoid possible decomposition of the bulb glass.
7) Protect lamp base,socket and wiring against moisture, corrosive atmospheres
and excessive heat.
8) Time should be allowed for lamps to stabilize in color when turned on for
the first time.This may require several hours of operation,with more than
one start.Lamp color is also subject to change under conditions of excess
vibration or shock,and color appearance may vary between individual lamps.
9) Lamps may require 10 to 20 minutes to re-light if there is a power interruption.
10) Take care in handling and disposing of lamps.If an arc tube is broken,avoid
skin contact with any of the contents or fragments.
Philips Lighting Company
200 Franklin Square Drive■P. O. Box 6800
Somerset,NJ 08875-6800
1-800-555-0050
www.lighting.philips.com/nam
A Division of Philips Electronics North America Corporation
Updated 7/03 MHC 011-A
Philips Lighting
281 Hillmount Road
Markham,Ontario
Canada L6C 2S3
1-800-555-0050
www.lighting.philips.com/nam
A Division of Philips Electronics Ltd.
MasterColor®Metal Halide 100 Watt ED-17 4K (Clear) Lamp Featuring ALTO®Lamp Technolo gy
Lamp Watts (Nominal). . . . . . . . . . . . . . . . . . . . . . . . . 100
Lamp Operating Voltage (rms) (Nominal)2
. . . . . . . . . . 102
Initial Lamp Voltage Range (rms)3
. . . . . . . . . . . . . . . . . 82–112
Lamp Operating Current (Amps) (rms) (Nominal). . . . 1.1
Lamp Current Crest Factor (Maximum). . . . . . . . . . . . 1.8
Warm-up Time to 80% of Output. . . . . . . . . . . . . . . . 2 Minutes
Re-strike Time for Hot Lamp. . . . . . . . . . . . . . . . . . . . 4–8 Minutes
Ballast Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI M140/M90/E
Ballast Open Circuit Voltage (Minimum). . . . . . . . . . . . 249 RMS Min.
Pulse Peak Volts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3300 Min.,4000 Max.
Pulse Width @ 90% Peak. . . . . . . . . . . . . . . . . . . . . . . 2 Micro Second Minimum
Pulse Repetition Rate (Minimum). . . . . . . . . . . . . . . . . 2 per Half Cycle
Minimum Operating Temperature. . . . . . . . . . . . . . . . . -30ºC