Philips BDP3010 SETUPS, TV Shape, HDMI Video Resolution, TV, 4:3, 4:3, Your, 16:9, 16:9, Video, Option, [HDMI], picture, (play)], 480i/60, monitor:, monitor:, monitor:

SETUPS

TV Shape

home A“Settings” A	“Advanced	A“Video Output” A “TV Shape”
	Setup”

Use this feature to adjust the aspect ratio of the video source which is different from your TV’s ratio to fit your TV monitor without distorting the picture. Descriptions of each setting are as follows:

Video	Your		Option	Description
source	TV
		4:3 Letter Box		To enjoy 16:9
				picture on 4:3
				monitor:
				16:9 picture is
				scaled down until
				both sides of the
				picture fits the 4:3
				TV.
	4:3	4:3 Pan & Scan		To enjoy 16:9
				picture on 4:3
				monitor:
				Both sides of the
16:9				picture are
				trimmed to fit the
				4:3 TV without
				distorting the
				aspect ratio of the
				picture.
		16:9 Widescreen		To enjoy 16:9
				picture on 16:9
				monitor:
				Select this setting
				when you want to
				enjoy 16:9 picture
				on the 16:9 TV.
	16:9	16:9 Squeeze		To enjoy 4:3
				picture on 16:9
				monitor:
				Use this setting to
4:3				display 4:3 picture
				on the 16:9 TV
				without distorting
				the aspect ratio of
				the picture.

HDMI Video Resolution

“Advanced “Video “HDMI “HDMI Video home A “Settings” A Setup” A Output” A Video” A Resolution”

Set the resolution of the video signal being output from the HDMI OUT jack.

You can select the desired “HDMI Video Resolution” among the settings listed below:

“Auto”,“480p”,“720p”,“1080i”,“1080p”

•When you make a selection, the TV monitor temporarily goes blank and then comes back again. If it does not, press [HDMI] to change the resolution or press and hold [B (play)] on the front panel for 5 seconds to change the setting back to its default.

Actual Output Resolution by Media:

										EN
	Media					BD
	Setting in					Source
	the “HDMI
	Video		480i/60		720p/60	1080i/60	720p/24		1080p/24
	Resolution”
	480p		480p/60		480p/60	480p/60	480p/60		480p/60
	720p	720p/60			720p/60	720p/60	720p/60		720p/60
	1080i	1080i/60			1080i/60	1080i/60	1080i/60		1080i/60
	1080p	1080p/60			1080p/60	1080p/60	1080p/60		1080p/24
									or 60(*1)
	Auto	The highest resolution supported by your display device
		will be in effect automatically.
(*1) To output the video in 24 Hz, the connected display device must										Introduction
	support 24 Hz output, and “HDMI 1080p/24” should be set to “Auto”.
	Otherwise, the image will be output in 60 Hz.
	Media				DVD	Photo viewing		OSD-only
								viewing
	Setting in the					Source
	“HDMI Video			480i/60
	Resolution”
										Connections
	480p			480p/60		480p/60		480p/60
	720p			720p/60		720p/60		720p/60
	1080i			1080i/60		1080i/60		1080i/60
	1080p			1080p/60		1080p/60		1080p/60
	Auto			The highest resolution supported by your display
				device will be in effect automatically.
• When HDMI cable is connected, only “480i” and the										Basic
	resolution selected in the “HDMI Video Resolution” will
	be available for the “Component Output”.									Setup
	480i/60.
• Composite video out (VIDEO OUT) can only output
	Note
	• The selected resolution must also be supported by									Playback
	your display device.
	• If your TV and the unit is connected by a DVI cable
	and if you select “Auto”, “480p” will be in effect
	automatically.
	• Pressing [B (play)] on the front panel for 5 seconds
	changes the setting back to its default.
	(“Component Output” setting will also be reset to									SetupFunction
	default (480i).)
	• Refer also to your TV’s manual.
										Others

EN 37