Hooking Up the TV/VCR, Rod Antenna | Philips CCB 134AT, CCB 194AT

6 Hooking Up the TV/VCR

1

Hook up your TV/VCR using one of the connections shown.

A.

Hooking Up Your TV/VCR With a Cable Signal or Outdoor Antenna

Connect a Cable signal or an antenna to the ANT(enna) Jack.

CCB134

ANT.

B.

Connect the Cable signal to the IN Jack on the Cable Box.

Hooking Up Your TV/VCR With a Cable Box

To view any channel, set the TV/VCR to the Cable Box output channel (channel 03 or 04). Then, select channels at the Cable Box.

Connect an RF coaxial cable (75- ohm, not supplied) to the OUT Jack on the Cable Box and to the ANT(enna) Jack on the TV/VCR.

CCB134

OUTIN

RF coaxial cable

(not supplied)

ANT.

	C.
	Hooking Up Your TV/VCR
	With an Indoor Antenna
	To install a rod antenna (not sup-	CCB134
	plied), push the stem of the antenna	CCB134
	plied), push the stem of the antenna
	into the antenna hole on the top of
	the TV/VCR. Connect the antenna
	wire to the ANT(enna) Jack on the
	back of the TV/VCR as shown.
	Extend the antenna and adjust its
	length, direction, and angle for the
	clearest picture.

Rod Antenna

(not supplied)

ANT.

Image 6

Philips CCB 134AT, CCB 194AT Hooking Up the TV/VCR, Hook up your TV/VCR using one of the connections shown, Rod Antenna

Contents

CCB134AT CCB194AT This bolt of lightning indi- cates uninsulated material Dear Philips product ownerFor Customer Use Model No Serial No Introduction FeaturesSafety Precautions Declaration of Conformity Table of Contents TV/VCR Maintenance Putting Batteries in the Remote ControlUsing the Remote Control Erasure Prevention Hook up your TV/VCR using one of the connections shown Hooking Up the TV/VCRRod Antenna Bent pin Hooking Up the TV/VCR cont’dAUDIO/VIDEO Jacks on front Crooked Pin Straight Pin Press the Combi button, then press the Power button Turning On the TV/VCRPress the Menu button. The screen shown below will appear Language Selection Press the Combi button, then press the Menu button Automatic Channel Setup Wait for the TV/VCR to set up channels Repeat steps 3-4 to add or delete other channels Adding/Deleting ChannelsPress the PLAY/o button or the STOP/p button to select Programming of the last channel you selected will appear Setting the Clock Manual Clock SettingCable Box users must set the clock manually Setting the Clock cont’d Setting the Clock cont’d Automatic PBS Channel Selection Wait for the TV/VCR to find TimeNOW Searching flashes on the TV/VCR screen Manual PBS Channel Selection Use the Number buttons to select your PBS station Wait for the TV/VCR to find the time Daylight-Savings Time Time Daylight Savings Time PRIM. SETUP. Then, press the F.FWD/B button Time ZonePress the PLAY/ button or the STOP/ button to select Setting the Remote to Operate a Cable Box/DBS Press the Mute buttonWithin 30 seconds, press the CABLE/DBS button Setting the Remote to Operate a Cable Box/DBS cont’d Power Button Earphone Jack Volume o/ p ButtonsWireless Remote Sensor Cassette Compartment ANTenna Jack AC Power CordRear Panel Connect your antenna or cable here Remote Control Buttons Memory Button VOLume m/ n ButtonPAUSE/STILL Button REWind/ Button When you finish, press the STATUS/EXIT button Adjusting the Picture ControlsAdjust the picture control. Refer to the chart on Press the REWind/ button or the F.FWD/B button to Decrease Increase Decreased brightness If you select Status ON, then select Counter only on On-Screen Status DisplaysIf you select Status ON, then select Counter only OFF If you select Status OFF Playing Insert a tape in the TV/VCR Power button to turn on the TV/VCR, if necessary RecordingPress the RECord/OTR button once to start recording One-Touch Recording OTR Rerecording Tape Duplication Different brands of equipment may operate differently Defeat Recording Follow the steps below to prevent accidental recording Timer Recording Lowed by the SET Clock menuDaily Timer Recording cont’d Timer Recording cont’d FM 0 Surf VOL Checking or Clearing Timer Recordings Setting Up the VCR Plus+ Programming System TV ChannelsStation Setting Up the VCR Plus+ Programming System cont’d Timer Recording With the VCR Plus+ Programming System You have completed the steps on pages Timer Recording With the VCR Plus+ Programming System cont’d Real-Time Counter Memory Appear on the screen ON-SCREEN Mode Defeat Recording OFF Repeat Play B Repeat Play Insert a tape in the TV/VCR Repeat Play cont’d Flashing a will become a flashing B Super High Speed Searching LP/SLP Playback OptionsForward and Reverse Searching SP/LP/SLP Viewing a Still Picture Blue Background SmartLock To block ratings, follow the steps below SmartLock cont’d Ratings are defined onExample Specific Sub-ratings To change the access code, follow these steps After you enter the code, the Smartlock menu will appear To check the SmartLock settings, follow these steps TV-Y7 Sleep Timer Timer during a recordingPress the Combi button, then press the SLEEP/WAKE UP button Wake Up Timer Menu Closed CaptionExample Screen Closed Caption cont’d Standard Closed CaptionsHalf-screen text Volume will stay at the same level Volume Bar/Smart SoundVolume Bar Smart Sound Automatic Operation Features FM Radio SmartPicture/FM RadioSmartPicture Follow the steps below to listen to FM radio stations If another remote control beeps Press the Mute button, then press the PAUSE/STILL button Reminder Press the Combi button, then press the Menu button Index Search Specifications Glossary Helpful Hints Helpful Hints cont’d Limited Warranty Please contact Philips at French Speaking English SpeakingModel # Serial # Index Supplied Accessories