4 |
5 |
English
Connect wires: ISO connectors
Caution
•Ensure that all loose leads are insulated with electrical tape.
1Pull out the ISO connectors from the car dashboard and connect them to the bigger
end of the supplied standard connector.
2Connect the other end of supplied standard connector to the unit.
3Do the other connections, if applicable.
Attach the front panel 
1Attach the trim plate.
2Insert the left side of the panel in the chassis until it is correctly engaged.
3Press the right side of the panel until the mechanism locks it into place.
4Close the front panel.
Mount in the dashboard 
Note
to avoid
2Ensure that car dashboard opening is within these measurements:
3Remove the two transport screws on the top of the unit.
4Remove the mounting sleeve with the re- moval keys.
5Install the sleeve into the dashboard and bend the tabs outward to fix the sleeve.
•If the unit is not fixed by sleeve but by the supplied screws, skip this step.
6Place the rubber cushion over the end of the bolt.
7Slide the unit into the dashboard until a click sound is heard.
8Reconnect the negative terminal of the car battery.
Detach the front panel
The front panel can be detached and taken with you to deter theft.
Note
•Before installing the unit, detach the front panel.
1Press 
to release the panel.
2Open the panel, then push the right side panel toward the left side to disengage it
from the chassis.
•When the unit is idle for over 5 minutes, it goes to standby mode and displays screen saver.
Set clock
1Press MENU.
2Press the navigation buttons to select [SET- TINGS], then press SEL on the remote control.
3Select [SYSTEM], then press 
.
4Select [TIME MODE], then press 
.
»The time mode options are displayed:
»[12 HOUR MODE]
»[24 HOUR MODE]
5Sselect a mode, then press SEL.
6Press 
to return to previous menu and select [TIME ADJUST], then press 
.
7Press 
or 
to enter clock, then press SEL.
Tune to a radio station
1Press SOURCE to selectTuner.
2Press 
or 
to select band.
»[FM] or [AM] is displayed.
3Press 
or 
to tune to a radio station manually.
•To search for radio station automatically, press 
or 
for 3 seconds.
»For video discs, if a menu appears: press
or 
to select an item, then press 
to start play.
»For discs that contain MP3s, WMAs, or JPEGs: , press 
or 
to select a folder/track/ picture, then press 
to start play.
Insert USB device 
1Slide down the USB socket cover.
2Insert the USB device into the USB socket.
»The unit starts playing from the USB device automatically.
Insert SD/MMC card 
1Press 
to open the front panel.
2Insert the SD or MMC card into the card slot.
»The unit starts playing from the SD/MMC card automatically.
6
•For proper operation of the DVD player, the chassis must be mounted within 20 degree horizontal. Ensure that the unit is mounted within this limitation.
1If the car does not have an
terminal of the car attery.
•If you disconnect the car battery in a car that has an
•If the car battery is not disconnected,
3Take off the panel and store it in the supplied carry case to protect it from dirt or damage.
Turn on
1Press the 
knob to turn on the unit.
»The unit plays the last listened program: DVD,Tuner, USB or SD/MMC Card (if there is USB device or SD/MMC card connected).
•To turn off the unit, press the 
knob for more than 2 seconds.
Play discs
1Press 
to open the front panel.
2Insert the disc into the disc slot with label side facing up.
»Play resumes from the point where it was last stopped.
3To remove the disc, press the 
button.
»When the disc is ejected, the unit switches toTUNER mode automatically.
4Close the front panel.
»After a few seconds, the screen turns on.
©2008 Koninklijke Philips Electronics N.V. All rights reserved.
