IFU Approbation / Safety Content RFX9400 | Philips guide

IFU Approbation / Safety Content RFX9400

FCC Compliancy

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rule.

These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a different circuit from the receiver.

•Consult the dealer or an experienced radio/TV technician for help.

CAUTION The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Notice for Canada / Remark pour le Canada

This class B digital apparatus complies with Canadian ICES-003.

Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada

i

Image 34

Philips manual IFU Approbation / Safety Content RFX9400, FCC Compliancy

Contents

Manual de inicio Page Starter’s Guide Contents Before You Start Stand-alone ModeNetwork Mode Stand-alone Advantages Pronto Wireless Extender Unpacking the Extender Wireless connection Configuring the ExtenderUse the default switch settings of the Extender Stand-alone Connection Configuration cable this is the crossed Extender will restart. After startup Connecting the Extender to AV-equipment Installing the ExtenderConfiguring the Extender through a Router Set the Extender’s Configuration switch to Support TroubleshootingWhat Do the LEDs Indicate? Finding the Exact Location of an AV-component’s IR Receiver Extender cannot communicate with the wireless networkAV-components do not respond to commands from the Extender Operating AV-components with the Extender Busy LED blinks green when the Control Panel is not in use Firmware UpdateResetting the Extender Updating the Extender with the configuration cable Pronto Wireless Extender Starter’s Guide SpecificationsRemarks Contenido Contenido del paquete del Extensor Modo Network modo red Antes de empezarModo Stand-alone modo autónomo Ventajas del modo Stand-alone Contenido del paquete del Extensor Conexión Network Configuración del ExtensorConexión Stand-alone Conexión inalámbrica Macro desde el Control Panel Conexión del Extensor a un equipo AV Configuración del Extensor a través de un routerInstalación del Extensor Abra ProntoEdit Professional en el PC Asistencia Detección de errores¿Qué indican los indicadores LED? Funcionamiento de los componentes AV con el Extensor El indicador LED WiFi está iluminado en rojoEl indicador LED WiFi parpadea en rojo Hay ID del Extensor duplicados Reinicialización del Extensor Actualización del Extensor con el cable de configuraciónActualización de Firmware Actualización del Extensor a través de un router Especificaciones Pronto Wireless Extender Manual de inicioObservaciones RFX9400FX9400 Guide deGuidedémarragede démarrage Table des matières Avantages du mode Stand-alone autonome Mode Stand-alone autonomeMode Network réseau Avantages du mode Network réseau Déballage du Prolongateur Connexion Network réseau Configuration du ProlongateurConnexion Stand-alone autonome Connexion filaire Branchez l’adaptateur secteur du Prolongateur Control Panel Placez le commutateur de configuration du Prolongateur sur Installation du ProlongateurConfiguration du Prolongateur par un routeur Connexion du Prolongateur à l’équipement audio/vidéo Ajustement du niveau de puissance des sorties IR DépannageQu’indiquent les voyants ? Il existe un conflit IP Le voyant WiFi est rouge et clignote Le voyant WiFi est rougeIl existe des ID de Prolongateur dupliqués Mise à jour du micrologiciel Configuration du Prolongateur par un routeurRéinitialisation du Prolongateur Spécifications Guide de démarrage du Pronto Wireless ExtenderRemarques IFU Approbation / Safety Content RFX9400 FCC Compliancy Regulations According to R&TTE Declaration Declaration of Conformity of this product can be found at Declaration of ConformityDoCMarking Iii Italian Smaltimento di vecchi prodotti French Mise au rebut des produits en fin de vieGerman Entsorgung Ihres alten Geräts Norwegian Avhending av gamle produkter Slovak Likvidácia tohto produktu Polish Usuwanie zużytych produktówEliminação do seu antigo produto Slovenian Odlaganje starega izdelka 3104 205