Configuring the Extender, Stand-alone Connection | Philips RFX9400

RFX9400 Starter’s Guide

Configuring the Extender

Note Before you start configuring the Extender, check if there are any firmware updates available in the Downloads section on www.pronto.philips.com.

Refer to the chapter ‘Firmware Update’ on page 9 for further details.

Stand-alone Connection

To configure the Stand-alone Extender:

1Plug in the Extender’s power adapter.

The Extender will start up. When start-up has finished, the Power and WiFi LEDs are green.

2Use the default switch settings of the Extender:

Stand-alone/Network	Stand-alone
Configuration switch	1
Extender ID	0

Note • If there is already an Extender with ID 0, set the Extender ID switch to an ID that is not used yet.

•If there is any interference with other products in or around the house, the Configuration switch can be set to a different RF channel.

•Make sure the same Extender ID and RF channel are used on the Extender and the Pronto Control Panel.

3Configure the Control Panel’s configuration file so that the Control Panel can work with the Extender. For more details, refer to the ProntoEdit Professional Online Help.

Network Connection

In the case of a network connection, the Extender is made part of the wireless Pronto Network. There are two ways to use the Extender in a network:

• Wired connection

Straight Ethernet Cable

Extender

Router

Control Panel

Wireless

Access Point

• Wireless connection

Extender

Control Panel

Wireless

Access Point

ENGLISH

4

Image 7

Philips RFX9400 manual Configuring the Extender, Stand-alone Connection, Network Connection, Wireless connection

Contents

Manual de inicio Page Starter’s Guide Contents Stand-alone Advantages Stand-alone ModeNetwork Mode Before You Start Unpacking the Extender Pronto Wireless Extender Stand-alone Connection Configuring the ExtenderUse the default switch settings of the Extender Wireless connection Extender will restart. After startup Configuration cable this is the crossed Set the Extender’s Configuration switch to Installing the ExtenderConfiguring the Extender through a Router Connecting the Extender to AV-equipment Support TroubleshootingWhat Do the LEDs Indicate? Operating AV-components with the Extender Extender cannot communicate with the wireless networkAV-components do not respond to commands from the Extender Finding the Exact Location of an AV-component’s IR Receiver Updating the Extender with the configuration cable Firmware UpdateResetting the Extender Busy LED blinks green when the Control Panel is not in use Pronto Wireless Extender Starter’s Guide SpecificationsRemarks Contenido del paquete del Extensor Contenido Ventajas del modo Stand-alone Antes de empezarModo Stand-alone modo autónomo Modo Network modo red Contenido del paquete del Extensor Conexión inalámbrica Configuración del ExtensorConexión Stand-alone Conexión Network Macro desde el Control Panel Abra ProntoEdit Professional en el PC Configuración del Extensor a través de un routerInstalación del Extensor Conexión del Extensor a un equipo AV Asistencia Detección de errores¿Qué indican los indicadores LED? Hay ID del Extensor duplicados El indicador LED WiFi está iluminado en rojoEl indicador LED WiFi parpadea en rojo Funcionamiento de los componentes AV con el Extensor Actualización del Extensor a través de un router Actualización del Extensor con el cable de configuraciónActualización de Firmware Reinicialización del Extensor Especificaciones Pronto Wireless Extender Manual de inicioObservaciones Table des matières RFX9400FX9400 Guide deGuidedémarragede démarrage Avantages du mode Network réseau Mode Stand-alone autonomeMode Network réseau Avantages du mode Stand-alone autonome Déballage du Prolongateur Connexion filaire Configuration du ProlongateurConnexion Stand-alone autonome Connexion Network réseau Control Panel Branchez l’adaptateur secteur du Prolongateur Connexion du Prolongateur à l’équipement audio/vidéo Installation du ProlongateurConfiguration du Prolongateur par un routeur Placez le commutateur de configuration du Prolongateur sur Il existe un conflit IP DépannageQu’indiquent les voyants ? Ajustement du niveau de puissance des sorties IR Le voyant WiFi est rouge et clignote Le voyant WiFi est rougeIl existe des ID de Prolongateur dupliqués Mise à jour du micrologiciel Configuration du Prolongateur par un routeurRéinitialisation du Prolongateur Spécifications Guide de démarrage du Pronto Wireless ExtenderRemarques FCC Compliancy IFU Approbation / Safety Content RFX9400 Declaration Regulations According to R&TTE Iii Declaration of ConformityDoCMarking Declaration of Conformity of this product can be found at Norwegian Avhending av gamle produkter French Mise au rebut des produits en fin de vieGerman Entsorgung Ihres alten Geräts Italian Smaltimento di vecchi prodotti Slovenian Odlaganje starega izdelka Polish Usuwanie zużytych produktówEliminação do seu antigo produto Slovak Likvidácia tohto produktu 3104 205