Checking or Cancelling Timer Recordings | Philips VRA471AT specification

Timer Recording (cont’d) 37

Checking or Cancelling Timer Recordings

1

With the VCR on and in VCR position (the VCR light will appear on the display panel), press the VCR button, then press the

MENU button.

POWER

VCR/TVSPEED

REC/OTR

2-4

EJECT

MEMORY

PAUSE/STILL

2

Press the PLAY/o button or the STOP/p button to select

PROGRAM, then press the F.FWD/B button.

31

Press the PLAY/o button or the STOP/p button to select PROGRAM REVIEW, then press the F.FWD/B button. The timer recording information for the program in the lowest numbered slot will appear on the screen. If no timer recordings are set, nothing will happen when you press the F.FWD/B button.

4

Press the F.FWD/B button repeatedly to review all pro- grammed timer recordings. If you don’t press the F.FWD/B button within 10 seconds, the VCR will automatically display infor- mation about the next programmed timer recording. This will continue until all timer recordings have been displayed. Then the menu will disappear.

	PLAY
REW	F.FWD
	STOP

				5
MENU	STATUS/EXIT	CLEAR

1 2 3

CH.

4 5 6

7 8 9

MUTE	0	ALT.CH	VOL.
			VOL.
VCR	TV	CBL/DBS
		VCR PLUS+
VAR.SLOW		/ENTER	SLOW
TRACKING		F.ADV	X2 PLAY
QUICK	TIME	INDEX REC END	SKIP
		SEARCH

5

To cancel the timer recording displayed, press the CLEAR button. Either the display will disappear or information about other timer recordings will appear. If you do not press any other buttons, the display will disappear after all timer recordings have been displayed.

6

Repeat steps 1-4 to make sure you have cleared the cor- rect timer recording.

Helpful Hints

•CLASH may flash on the screen when you finish setting a timer recording. This means that the timer recording you just pro- grammed and another timer record- ing overlap. The current timer recording will not take place. You may choose to cancel the overlap- ping timer recording.

•To stop a started timer recording, press the STOP/EJECT button on the VCR.

See page 56 for more hints.

Image 37

Philips VRA471AT owner manual Checking or Cancelling Timer Recordings, See page 56 for more hints

Contents

VRA471AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial No Introduction Features Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front Panel Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System Plug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’d Hookups With a Cable Box/Direct Broadcast System Cable Signal RF coaxialConnections Recording/Viewing Any Channel Connect a Cable signal to the VCR’s ANTenna in Jack Cable SignalRecording One Channel/Watching Another Cable Box/DBS Hookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Press the VCR button Press the Menu button Automatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels Do each step within 60 seconds of the previous step Manual Clock Setting Setting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock Setting Time Zone Daylight-Savings Time Language Selection 2TV code Setting the Remote to Operate a TV Cable BOX Codes Remote Control Buttons Remote Control Buttons cont’d RECord/OTR Button REWind/ ButtonMenu Button Number Buttons Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFF VCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR Press the Eject button to remove the tape Turn on the TV and set it to channel 3 or 4, whichever RecordingIf the VCR light appears on the display panel, go to . If OTR CH12 One-Touch Recording Recording One Channel/Watching Another Daily Timer Recording Timer Recording cont’d Tape Speeds Timer Recording cont’d See page 56 for more hints Checking or Cancelling Timer Recordings Channels Setting Up the VCR Plus+ Programming SystemCall Letters Examine the lists on Setting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Set the program to Be recorded on the satellite tuner Auto DBS RecordLink RF coaxial cable Rerecording Tape Duplication Press the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Automatic Operation Features Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Playing a Tape at Double Speed Viewing a Slow Motion Picture Viewing a Still PictureDuring tape playback, press the PAUSE/STILL button. a Still picture will appear on the screen During the timer recording When Child Lock is activatedTV and Cable Box/DBS feature buttons of the remote Child Lock Letting your VCR find your remote for you If another remote control beepsPress the Mute button, then press the PAUSE/STILL button Press the VCR button Press the Time Search button Time Search Press the VCR button Press the Index Search button Example Skip Search Record End Search To resume normal tape playback, press the PLAY/o button Quick Search Real-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or Glossary Specifications Model # Serial # Limited Warranty Remote control PowerTimer AutomaticPage Page Supplied Accessories