Press the STATUS/EXIT button. Program WAS COM | Philips VRA471AT

Timer Recording with the VCR Plus+ Programming System (cont’d) 41

5

Press the Number 1 button to record in SP speed or the Number 2 button to record in SLP speed. Your selection will appear beside REC SPEED on the screen; SP=1 SLP=2 will continue to flash. For details about tape speed, see pages 36 and 58. You cannot use the SPEED button at this time.

ONE TIME PROGRAM

PROGRAM	1
CHANNEL	09
TIME ON	10:30 PM
TIME OFF	11:30 PM
REC SPEED	SLP
SP=1 SLP=2
START DATE	10/10/99
	SUN.

TO END PUSH EXIT

6

Press the STATUS/EXIT button. PROGRAM WAS COM-

PLETED PLEASE TURN OFF VCR FOR TIMER RECORDING should appear on the screen briefly.

7

Press the POWER button to turn off the VCR power. The Timer light will appear. The Timer light will flash if there is not a tape in the VCR.

If the timer recording will take place several hours or days from now, you may use the VCR until time for the recording. Just turn off the VCR a few minutes before the recording starts. If you for- get to turn off the VCR, PLEASE TURN OFF VCR FOR TIMER RECORDING flashes on your TV screen two minutes before a timer recording starts. Remove the message by pressing the CLEAR button.

7	POWER		EJECT
7	VCR/TV		SPEED	MEMORY
	REC/OTR			PAUSE/STILL
			PLAY
	REW		F.FWD
			STOP
	MENU	STATUS/EXIT		CLEAR
5	1	2	3
	4	5	6	CH.
	4	5	6
	7	8	9
	MUTE	0	ALT.CH	VOL.
				VOL.
	VCR	TV	CBL/DBS
			VCR PLUS+
	VAR.SLOW		/ENTER	SLOW
	TRACKING		F.ADV	X2 PLAY
	QUICK	TIME	INDEX REC END	SKIP
			SEARCH

6

Turn off the VCR for the recording.

Insert a tape in the VCR.

Leave the Cable Box/DBS on

(if applicable).

Helpful Hints

•To stop a started timer recording, press the STOP/EJECT button on the VCR.

•If you are using a Cable Box/DBS, timer recordings are programmed differently. See pages eight and 38-39 for details.

•You may use the VCR Plus+ Programming System to record pro- grams on Cable TV channels up to channel 99.

See page 56 for more hints.

Image 41

Philips VRA471AT owner manual Press the STATUS/EXIT button. Program WAS COM, See page 56 for more hints

Contents

VRA471AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial No Introduction Features Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front Panel Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System Plug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’d Hookups With a Cable Box/Direct Broadcast System Cable Signal RF coaxialConnections Recording/Viewing Any Channel Connect a Cable signal to the VCR’s ANTenna in Jack Cable SignalRecording One Channel/Watching Another Cable Box/DBS Hookups With a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCR2Turn on the TV Press the VCR button Press the Menu button Automatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels Do each step within 60 seconds of the previous step Manual Clock Setting Setting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock Setting Time Zone Daylight-Savings Time Language Selection 2TV code Setting the Remote to Operate a TV Cable BOX Codes Remote Control Buttons Remote Control Buttons cont’d RECord/OTR Button REWind/ ButtonMenu Button Number Buttons Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFF VCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR Press the Eject button to remove the tape If the VCR light appears on the display panel, go to . If RecordingTurn on the TV and set it to channel 3 or 4, whichever OTR CH12 One-Touch Recording Recording One Channel/Watching Another Daily Timer Recording Timer Recording cont’d Tape Speeds Timer Recording cont’d See page 56 for more hints Checking or Cancelling Timer Recordings Call Letters Setting Up the VCR Plus+ Programming SystemChannels Examine the lists on Setting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Set the program to Be recorded on the satellite tuner Auto DBS RecordLink RF coaxial cable Rerecording Tape Duplication Press the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select Automatic Operation Features Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Playing a Tape at Double Speed Viewing a Slow Motion Picture Viewing a Still PictureDuring tape playback, press the PAUSE/STILL button. a Still picture will appear on the screen During the timer recording When Child Lock is activatedTV and Cable Box/DBS feature buttons of the remote Child Lock Press the Mute button, then press the PAUSE/STILL button If another remote control beepsLetting your VCR find your remote for you Press the VCR button Press the Time Search button Time Search Press the VCR button Press the Index Search button Example Skip Search Record End Search To resume normal tape playback, press the PLAY/o button Quick Search While the status display is on the screen, press Clear button to reset the real-time counter to zeroReal-Time Counter Memory Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or Glossary Specifications Model # Serial # Limited Warranty Remote control PowerTimer AutomaticPage Page Supplied Accessories