Plug in the TV and the VCR | Philips VRA471AT specification

Hookups Without a Cable Box/Direct Broadcast System (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

ANT

IN

				AUDIO
			ANT	OUT IN	OUT
			ANT	VIDEO	CH3 CH4
			IN		75V
					75V
					ANT	/
AUDIO					CABLE
AUDIO
OUT	IN		OUT			ANTENNA IN Jack
						ANTENNA IN Jack
VIDEO		CH3	CH4			(on back of TV)
		CH3	CH4		RF coaxial cable	example only
						example only

4

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

CH3 CH4

ANT

IN

ANT

IN

AUDIO

OUT

IN

OUT

VIDEO CH3 CH4

AUDIO
OUT	IN	OUT
VIDEO		CH3 CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Philips VRA471AT owner manual Hookups Without a Cable Box/Direct Broadcast System cont’d, Plug in the TV and the VCR

Contents

VRA471AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use This bolt of lightning indi- cates uninsulated material Introduction Features Table of Contents Removing the Plastic Cover from the Front Panel Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System Plug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’d Recording/Viewing Any Channel Cable Signal RF coaxialHookups With a Cable Box/Direct Broadcast System Connections Cable Box/DBS Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Recording One Channel/Watching Another Hookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Press the VCR button Press the Menu button Automatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels Do each step within 60 seconds of the previous step Manual Clock Setting Setting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock Setting Time Zone Daylight-Savings Time Language Selection 2TV code Setting the Remote to Operate a TV Cable BOX Codes Remote Control Buttons Remote Control Buttons cont’d Number Buttons REWind/ ButtonRECord/OTR Button Menu Button If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only on VCR Display Panel Front Panel Rear Panel Press the Eject button to remove the tape PlayingRead and follow the steps below to play a tape 1Turn on the TV 2Insert a tape in the VCR Turn on the TV and set it to channel 3 or 4, whichever RecordingIf the VCR light appears on the display panel, go to . If OTR CH12 One-Touch Recording Recording One Channel/Watching Another Daily Timer Recording Timer Recording cont’d Tape Speeds Timer Recording cont’d See page 56 for more hints Checking or Cancelling Timer Recordings Channels Setting Up the VCR Plus+ Programming SystemCall Letters Examine the lists on Setting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Set the program to Be recorded on the satellite tuner Auto DBS RecordLink RF coaxial cable Rerecording Tape Duplication Press the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Automatic Operation Features Playing a Tape at Double Speed Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLP Still picture will appear on the screen Viewing a Still PictureViewing a Slow Motion Picture During tape playback, press the PAUSE/STILL button. a Child Lock When Child Lock is activatedDuring the timer recording TV and Cable Box/DBS feature buttons of the remote Letting your VCR find your remote for you If another remote control beepsPress the Mute button, then press the PAUSE/STILL button Press the VCR button Press the Time Search button Time Search Press the VCR button Press the Index Search button Example Skip Search Record End Search To resume normal tape playback, press the PLAY/o button Quick Search Real-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or Glossary Specifications Model # Serial # Limited Warranty Automatic PowerRemote control TimerPage Page Supplied Accessories