Letting your VCR find your remote for you | Philips VRA471AT

Letting your VCR find your remote for you...

1

Press the POWER button on the VCR to turn on the VCR. Your remote control beeps and LOCATING REMOTE appears on the screen. The remote control will beep for about 30 seconds. (The

Remote Locator 49

If another remote control beeps...

POWER	EJECT

VCR/TVSPEED MEMORY

exception is when you plug the VCR power cord into the wall outlet for the first time.) Or, press any button on the remote control to stop the beeping.

If another remote control beeps...

The VCR may find other remote controls. If this occurs, follow the steps below to program the VCR to find only its remote control.

1

Press the VCR button, then press the MENU button.

2

Press the PLAY/o button or the STOP/p button to select REMOTE LOCATOR, then press the F.FWD/B button.

PRESS MUTE THEN

2

5

1

REC/OTR

PLAY

REW

STOP

MENU
MENU		STATUS/EXIT
		STATUS/EXIT

1 2 3

4 5 6

7 8 9

MUTE 0 ALT.CH

VCR TV CBL/DBS

VCR PLUS+

VAR.SLOW/ENTER

PAUSE/STILL 3

F.FWD

CLEAR

CH.

4

VOL.

SLOW3

PAUSE KEY

TO CHANGE CODE FROM 4

TO END PUSH EXIT

3

Press the MUTE button, then press the PAUSE/STILL button.

YOUR REMOTE LOCATOR

CODE IS 4

PRESS ANY DIGIT

TO CHANGE CODE

TO END PUSH EXIT

4

Press one Number button (0 - 9) to enter a new single-digit code for your remote control. Your remote control will beep briefly.

YOUR REMOTE LOCATOR

CODE HAS BEEN CHANGED

NEW CODE IS 3

TO END PUSH EXIT

5

Press the STATUS/EXIT button.

TRACKING	F.ADV	X2 PLAY
QUICK TIME	INDEX REC END	SKIP
	SEARCH

This device complies with part 15 of the FCC Rules. Operation is subject to the following two con- ditions: (1) This device may not cause harmful interference, and (2) this device must accept any inter- ference received, including inter- ference that may cause undesired operation.

Helpful Hints

•If there are no batteries in the remote control, it will not beep.

•The TV volume may be muted while the LOCATING REMOTE message appears on the screen. Press the STATUS/EXIT button on the VCR remote control to remove the mes- sage and restore the volume.

Image 49

Philips VRA471AT owner manual Letting your VCR find your remote for you, If another remote control beeps

Contents

VRA471AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial No Introduction Features Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front Panel Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System Plug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’d Hookups With a Cable Box/Direct Broadcast System Cable Signal RF coaxialConnections Recording/Viewing Any Channel Connect a Cable signal to the VCR’s ANTenna in Jack Cable SignalRecording One Channel/Watching Another Cable Box/DBS Hookups With a Stereo TV 2Turn on the TV Turning on Your VCRPress the Menu button. The display shown below will appear Press the VCR button Press the Menu button Automatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels Do each step within 60 seconds of the previous step Manual Clock Setting Setting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock Setting Time Zone Daylight-Savings Time Language Selection 2TV code Setting the Remote to Operate a TV Cable BOX Codes Remote Control Buttons Remote Control Buttons cont’d RECord/OTR Button REWind/ ButtonMenu Button Number Buttons Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFF VCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR Press the Eject button to remove the tape Turn on the TV and set it to channel 3 or 4, whichever RecordingIf the VCR light appears on the display panel, go to . If OTR CH12 One-Touch Recording Recording One Channel/Watching Another Daily Timer Recording Timer Recording cont’d Tape Speeds Timer Recording cont’d See page 56 for more hints Checking or Cancelling Timer Recordings Channels Setting Up the VCR Plus+ Programming SystemCall Letters Examine the lists on Setting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System Press the STATUS/EXIT button. Program WAS COM Set the program to Be recorded on the satellite tuner Auto DBS RecordLink RF coaxial cable Rerecording Tape Duplication Press the PLAY/o button or the STOP/p button to select Repeat PlayPress the F.FWD/B button so that on appears beside Automatic Operation Features Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Playing a Tape at Double Speed Viewing a Slow Motion Picture Viewing a Still PictureDuring tape playback, press the PAUSE/STILL button. a Still picture will appear on the screen During the timer recording When Child Lock is activatedTV and Cable Box/DBS feature buttons of the remote Child Lock Letting your VCR find your remote for you If another remote control beepsPress the Mute button, then press the PAUSE/STILL button Press the VCR button Press the Time Search button Time Search Press the VCR button Press the Index Search button Example Skip Search Record End Search To resume normal tape playback, press the PLAY/o button Quick Search Real-Time Counter Memory Clear button to reset the real-time counter to zeroWhile the status display is on the screen, press Blue Background Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or Glossary Specifications Model # Serial # Limited Warranty Remote control PowerTimer AutomaticPage Page Supplied Accessories