Press the Time Search button | Philips VRA601AT manual

Follow the steps below to program the VCR to search forward or backward on a tape a specific length of time. There must be a tape in the VCR.

1

Press the TIME SEARCH button.

TIME SEARCH

0:00

ENTER SEARCH TIME

2

Within 10 seconds, use the Number buttons to enter the desired length of time you want to skip forward or back- ward. For example, for 1 hour, 25 minutes, press Number but- tons 1, 2, 5. Or, for five minutes, press Number buttons 0, 0, 5.

3

Within 10 seconds, press the F.FWD/B button or the REWIND/{ button. The VCR will skip over the specified length of time, then begin playback.

Time Search 35

	POWER		VCR/TV	EJECT
2	1	2	3
	4	5	6
	7	8	9	CHANNEL
1		0
	SPEED	TIME SEARCH		MEMORY
	MENU	STATUS/EXIT	CLEAR	SLOW
3	REWIND	/PLAY		F.FWD
3	REC/OTR	/STOP		PAUSE/STILL

Helpful Hints

•If you want to search for more than 59 minutes, you must enter the length of time in hours and minutes. For example, to search forward 70 minutes, press 1,1,0 at step 2.

•You can not do a Time Search while recording.

•To remove the Time Search display, press the TIME SEARCH button again.

•To cancel a Time Search that is in progress, press the STOP/p button.

Image 35

Philips VRA601AT owner manual Press the Time Search button

Contents

VRA601AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use This bolt of lightning indi- cates uninsulated material Introduction FeaturesSafety Precautions Table of Contents Removing the Plastic Cover from the Front Panel Before Using Your VCRPutting Batteries in the Remote Control VCR maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast System Plug in the TV and the VCR Hookups Without a Cable Box/Direct Broadcast System cont’d Recording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Recording One Channel/Watching Another Video Cable Hookups With a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCR2Turn on the TV Press the Menu button Automatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels You make each entry within 60 seconds of the previous entry Follow the steps below to set your VCR’s clock. Make sure Daylight-Savings Time Language Selection Remote Control Buttons Clear Button Remote Control Buttons cont’dEject Button Press to eject the tape If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only on VCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape RECord light will appear RecordingInsert a tape with its record tab intact in the VCR Recording One Channel/Watching Another One-Touch Recording Daily Timer RecordingDo each step within 60 seconds of the previous step Timer Recording cont’d Tape Speeds Timer Recording cont’d Checking or Cancelling Timer Recordings RF coaxial cable Rerecording Tape Duplication Press the F.FWD/B button so that on appears beside Repeat PlayPress the PLAY/o button or the STOP/p button to select Real-Time Counter Memory Press the Time Search button Time Search Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLP Automatic Operation Features Monitor Multi-Channel Television Sound SystemUnderstanding On-Screen Displays Specifically… Multi-Channel Television Sound System cont’d Hi-Fi Stereo Sound System Please see additional notes on Hi-Fi Stereo Sound System cont’dHIFI. on will appear to the right of Hifi on the screen Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or Glossary Specifications Model # Serial # Limited Warranty Automatic PowerRemote control Timer Supplied Accessories