Press the STATUS/EXIT button. Program WAS COM | Philips VRA633AT

Timer Recording with the VCR Plus+ Programming System (cont’d) 41

5

Press the Number 1 button to record in SP speed or the Number 2 button to record in SLP speed. Your selection will appear beside REC SPEED on the screen; SP=1 SLP=2 will continue to flash. For details about tape speed, see pages 36 and 54. You cannot use the SPEED button at this time.

ONE TIME PROGRAM

PROGRAM	1
CHANNEL	09
TIME ON	10:30 PM
TIME OFF	11:30 PM
REC SPEED	SLP
SP=1 SLP=2
START DATE	10/10/99
	SUN.
TO END PUSH EXIT

7	POWER	VCR/TV	EJECT
7	VCR	TV	CBL/DBS

PLAY

REWF.FWD

STOP

6

5

MENU

STATUS/EXIT	CLEAR

1

4

7

2 3

5 6

8 9

CH

VCR PLUS+/ENTER

ALT. CH

0VOL

6

Press the STATUS/EXIT button. PROGRAM WAS COM-

PLETED / PLEASE TURN OFF VCR FOR TIMER RECORDING should appear on the screen briefly.

7

SPEED TIME SEARCH PAUSE/STILL

REC/OTR MEMORY SLOW MUTE

Press the POWER button to turn off the VCR power. The Timer light will appear. The Timer light will flash if there is not a tape in the VCR.

If the timer recording will take place several hours or days from now, you may use the VCR until time for the recording. Just turn off the VCR a few minutes before the recording starts. If you for- get to turn off the VCR, PLEASE TURN OFF VCR FOR TIMER RECORDING flashes on your TV screen two minutes before a timer recording starts. Remove the message by pressing the CLEAR button.

Turn off the VCR for the recording.

Insert a tape in the VCR.

Leave the Cable Box/DBS on

(if applicable).

Helpful Hints

•You may use the VCR Plus+ Programming System to record pro- grams on Cable TV channels up to channel 99.

•To stop a started timer recording, press the STOP/EJECT button on the VCR.

•If the power fails for more than one minute, programmed timer recordings may be lost. Reset the clock before resetting the timer recordings.

•If you are using a Cable Box/DBS, timer recordings are programmed differently. See pages eight and 38-39 for details.

See page 52 for more hints.

Image 41

Philips VRA633AT owner manual Press the STATUS/EXIT button. Program WAS COM, See page 52 for more hints

Contents

VRA633AT For Customer Use Dear Philips Magnavox product ownerThis bolt of lightning indi- cates uninsulated material Model No Serial No Introduction FeaturesSafety Precautions Table of Contents Using the Remote Control Putting Batteries in the Remote ControlVCR maintenance Removing the Plastic Cover from the Front Panel Disconnect the antenna or cable from your TV Hookups without a Cable Box/Direct Broadcast System Plug in the TV and the VCR Hookups without a Cable Box/Direct Broadcast System cont’d Recording/Viewing Any Channel Hookups with a Cable Box/Direct Broadcast SystemConnections TV’s Antenna Recording One Channel/Watching AnotherCable Box/DBS Hookups with a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCR2Turn on the TV Press the VCR button Press the Menu button Automatic Channel Setup Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized Channels Do each step within 60 seconds of the previous step Setting the ClockManual Clock Setting Setting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock Setting Time Zone Press the VCR button Daylight-Savings Time Language Selection Child Lock When Child Lock is activated Press the Mute button 2Find your TV code Your code 2Find VOLume o/p Button Press to adjust the volume of your TV Remote Control ButtonsEject Button VCR Button Menu REWind/ ButtonVCR PLUS+/ENTER Button Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFF VCR Display Panel Timer LightCassette Compartment VCR Light Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape If the VCR light appears on the display panel, go to . If RecordingVCR light does not appear, press the VCR/TV button once RECord light will appear Recording One Channel/Watching Another Press the VCR button, then press the CHannel o/p but One-Touch Recording Daily Timer Recording Timer Recording cont’d Tape Speeds Timer Recording cont’d Checking or Cancelling Timer Recordings Call Letters Setting Up the VCR Plus+ Programming SystemChannels Examine the lists on Setting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System See page 52 for more hints Press the STATUS/EXIT button. Program WAS COM RF coaxial cable Rerecording Tape Duplication Press the F.FWD/B button so that on appears beside VCR SET UP, then press the F.FWD/B buttonRepeat Play Real-Time Counter Memory Press the VCR button Press the Time Search button Time Search Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still Picture Automatic Operation Features Understanding On-Screen Displays Multi-Channel Television Sound SystemSpecifically… Monitor Multi-Channel Television Sound System cont’d → Hifi Mono To END Push Exit Hi-Fi Stereo Sound System Please see additional notes on Hi-Fi Stereo Sound System cont’d Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or Glossary Specifications Model # Serial # Limited Warranty Index Page Page Supplied Accessories