To erase the recorded contents of a tape, load the tape in DECK II (or I) and follow the procedure below.
| lill | "lit |
I _ | _ I _ _ _ | _,''" |
| .] | .] |
(3)(2)3 1 2
1.Set the REC LEVEL control to the MIN position.
2.Press the recording (e) button.
3.Press the playback (l_or 4) button or the pause (11) button.
AUTO BLE TUNING
When tuning DECK II (or I).
3 23
o
o
o
1.Load a tape in DECK II (or I).
•The AUTO BLE does not work when the erasure prevention tabs of the loaded cassette tape have been broken off.
2.Set the REV MODE switch to _ or
3.Press the BLE button of DECK II (or I).
The II (or I) indicator will flash in the AUTO BLE display for about 30 seconds, after which it will light steadily.
The tape will be forwarded for approximately one second after pressing the start button so that recording will start from the recordable portion of the tape.
The operation is completed when the start position is resumed.
When tuning both decks in sequence (except for
1.Load tapes in both decks.
2.Set the REV MODE switch to _ (RELAY/SKIP).
3.Press the BLE button of DECK I.
Auto BLE tuning starts from DECK I to DECK II.
•If the BLE button of DECK II is pressed, the tuning will stop after only DECK II is tuned.
•A tuning signal will be recorded on the cassette in the cas- sette deck when using AUTO BLE. The music and other in- formation already recorded on this cassette will be erased from the point where tuning starts.
|
|
|
| RECORDING | |
BLE | operation |
| AUTO | BLE indicator |
|
DECK | I tuning |
|
| B] _ | Flashes |
DECK | I tuned | Lights | _ | aLE] |
|
|
|
| |||
DECK | II tuning | Lights |
| BLE_ | Flashes |
|
|
| • I 11 |
| |
DECK | II tuned | Lights | i | P =ILl= | Lights |
|
| I II - | |||
|
|
|
|
To stop AUTO BLE tuning
To cancel AUTO BLE tuning (e.g. must record urgently), press the stop ( • ) button.
To reset a tuned condition
Press the BLE button again.
Error display
•If the old tape, the tape end or the leader (white portion) im- mediately prior to the tape end is reached during AUTO BLE oper- ation, tuning becomes impossible. That means recording will stop immediately and the counter indicator will display the fol- lowing (flashing) message: "Err".
In this case, press the BLE button again to reset, and record without AUTO BLE tuning.
The following illustrates the operation:
(Operation completed within approximately 30 seconds)
Each operation is shown on the left and right channel level meters during AUTO BLE tuning.
Display
Counter indicator
START
FI N, I-I J-I
LI LI. L; Lt (Normal counter)
(D
• Adjusting | recording | bias. |
|
|
|
|
| £1 | e | t ! | _! |
• Adjusting | recording | level | l- | J/ | I |
(sensitivity). | I | ||||
L | t/ | L | |||
® |
|
|
|
|
|
• Adjusting | recording |
| I- |
| |
equalizer. |
|
|
| ||
|
| C | Uf |
| |
|
|
|
| ||
STOP |
|
|
|
|
|
END |
| Ft. | |||
| LI | I._t- t f I_1 | |||
|
| ||||
|
| (Return to | normal | counter) |
15
<RRB1143>
En