Pioneer DEH-P5200HD operation manual Initial Settings, SLA source level adjustment

Operating this unit

Section

02

SLA (source level adjustment)

SLA (Source level adjustment) lets you adjust the vo- lume level of each source to prevent radical changes in volume when switching between sources.

!When selecting FM as the source, you cannot switch to SLA.

!Settings are based on the FM volume level, which remains unchanged.

Before adjusting source levels, compare the FM volume level with the level of the source you wish to adjust.

!The AM volume level can also be adjusted with source level adjustments.

1Press M.C. to display the setting mode.

2Turn M.C. to adjust the source volume. Adjustment range: +4 to –4

3Press M.C. to confirm the selection.

Note

Operation is complete even if the menu is can- celled before being confirmed.

Initial Settings

1Press SRC/OFF and hold until the unit turns off.

2Press M.C. and hold until the initial set- ting menu appears in the display.

3Turn M.C. to select the initial setting. After selecting, perform the following proce- dures to set the initial setting.

Clock (setting the clock)

1Press M.C. to display the setting mode.

2Press M.C. to select the segment of the clock dis- play you wish to set.

Hour—Minute

As you select segments of the clock display, the selected segment flashes.

3Turn M.C. to adjust the clock.

Clock (clock on/off setting)

1Press M.C. to turn the clock display on or off.

AUX1/AUX2 (auxiliary input setting)

Activate this setting when using auxiliary device con- nected to this unit.

1Press M.C. to turn AUX on or off.

USB PnP (plug and play)

This setting allows you to switch your source to USB/ USB-iPod automatically.

1Press M.C. to turn the plug and play on or off. ON – When USB storage device/iPod is con- nected, the source is automatically switched to USB/USB-iPod. If you disconnect your USB sto- rage device/iPod, this unit’s source is turned off. OFF – When USB storage device/iPod is con- nected, the source is not switched to USB/USB- iPod automatically. Please change the source to USB/USB-iPod manually.

Brightness (display brightness setting)

1Press M.C. to display the setting mode.

2Turn M.C. to switch the brightness setting. High (high)—Low (low)

3Press M.C. to confirm the selection.

SW control (rear output and subwoofer setting)

The rear speaker leads output (Rear SP) and RCA out- put (Preout) of this unit can be used for full-range speaker (Rear SP :FULL/Preout :Rear) or subwoofer (Rear SP :SUBW/Preout :SUBW) connection. If you switch to Rear SP :SUBW, you can connect a rear speaker lead directly to a subwoofer without using an auxiliary amp.

Initially, Rear SP is set for rear full-range speaker con- nection (FULL). When Rear SP :FULL is selected, you can connect the RCA output to a subwoofer. In this case, you can select whether to use the subwoofer controller’s (low pass filter, phase) built-in Preout : SUBW or the auxiliary Preout :Rear.

1Press M.C. to display the setting mode.

2Press M.C. to cycle between as following: Rear SP/Preout—FULL (SUBW)/SUBW(Rear)

3Turn M.C. to change the setting. Rear SP: FULL—SUBW Preout: SUBW—Rear

!Even if you change this setting, there is no output unless you turn the subwoofer output on (refer to SW setting 1 (subwoofer on/off setting) on the previous page).

!If you change this setting, subwoofer output in the audio menu will return to the factory settings.

DEMO (demo display setting)

1Press M.C. tp turn the demo display on or off.

English

En 15