Connecting the Units
Note:
• This unit is for vehicles with a |
negative grounding. Before installing it in a recre- |
ational vehicle, truck, or bus, check the battery |
voltage. |
• To avoid shorts in the electrical system, be sure to |
disconnect the ≠ battery cable before beginning |
installation. |
• Refer to the owner’s manual for details on |
• When an external power amp is being used with |
this system, be sure not to connect the blue/white |
lead to the amp’s power terminal. Likewise, do not |
connect the blue/white lead to the power terminal |
of the |
excessive current drain and malfunction. |
• To avoid a |
lead with insulating tape. Insulate the unused |
7 When not connecting a rear speaker lead to a Subwoofer
Connecting cords with RCA pin plugs (sold separately)
| Rear output | |
|
| |
This product | Front output | 15 cm |
|
|
<ENGLISH>
Power amp (sold separately)
Power amp (sold separately)
MANUAL
DEH-P5800MP
MANUEL
connecting the power amp and other units, then |
make connections correctly. |
• Secure the wiring with cable clamps or adhesive |
tape. To protect the wiring, wrap adhesive tape |
around them where they lie against metal parts. |
• Route and secure all wiring so it cannot touch any |
moving parts, such as the gear shift, handbrake and |
seat rails. Do not route wiring in places that get |
hot, such as near the heater outlet. If the insulation |
of the wiring melts or gets torn, there is a danger of |
the wiring |
• Don’t pass the yellow lead through a hole into the |
engine compartment to connect to the battery. This |
will damage the lead insulation and cause a very |
dangerous short. |
• Do not shorten any leads. If you do, the protection |
circuit may fail to work when it should. |
• Never feed power to other equipment by cutting |
the insulation of the power supply lead of the unit |
and tapping into the lead. The current capacity of |
the lead will be exceeded, causing overheating. |
• When replacing the fuse, be sure to only use a fuse |
of the rating prescribed on this unit. |
• Since a unique BPTL circuit is employed, never |
wire so the speaker leads are directly grounded or |
speaker leads without fail. There is a possibility of |
a |
• To prevent incorrect connection, the input side of |
the |
is black. Connect the connectors of the same |
colors correctly. |
• If this unit is installed in a vehicle that does not |
have an ACC (accessory) position on the ignition |
switch, the red lead of the unit should be connected |
to a terminal coupled with ignition switch ON/OFF |
operations. If this is not done, the vehicle battery |
may be drained when you are away from the vehi- |
cle for several hours. (Fig.1) |
|
| CC |
|
|
|
|
|
|
|
|
| F | A | O |
|
|
| F | O |
|
|
|
| N |
| N | ||||||
O | F |
|
|
|
| O | F |
|
|
|
|
|
|
| S |
|
|
| S | ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| T |
|
|
|
| T |
|
|
|
| R | A |
|
|
| R | A |
|
|
| T |
|
|
| T |
| ||
ACC position | No ACC position |
Fig. 1
Subwoofer output or non fading output
Antenna jack | Fuse (10 A) | |
|
|
|
|
|
|
Yellow/black
If you use an equipment with Mute function, wire this lead to the Audio Mute lead on that equipment. If not, keep the Audio Mute lead free of any connections.
Yellow
To terminal always supplied with power regardless of ignition switch position.
Jack for the Wired Remote Control Adaptors
Please see the Instruction Manual for the
Wired Remote Control Adaptors (sold separately).
|
| |
(sold separately) |
| |
Blue/white |
|
|
To system control terminal of the power amp or |
| |
| ||
mA 12 V DC). |
|
|
|
| System remote control |
| + | + |
| Front speaker |
|
| ≠ | ≠ |
Power amp (sold separately)
Front speaker
Le code de couleur des câbles utilisé pour ce produit est conforme à CEMA.
Printed in Thailand
Imprimé en Thaïlande
<KMINX> <05H00000> |
the left and right ≠ speaker leads are common. |
• Speakers connected to this unit must be high- |
power with minimum rating of 50 W and imped- |
ance of 4 to 8 ohms. Connecting speakers with out- |
put and/or impedance values other than those |
noted here may result in the speakers catching fire, |
emitting smoke or becoming damaged. |
• When this product’s source is switched ON, a con- |
trol signal is output through the blue/white lead. |
Connect to an external power amp’s system remote |
control or the car’s |
minal (max. 300 mA 12 V DC). If the car features |
a glass antenna, connect to the antenna booster |
power supply terminal. |
•The black lead is ground. Please ground this lead separately from the ground of
If you ground the products together and the ground becomes detached, there is a risk of damage to the products or fire.
•Cords for this product and those for other products may be different colors even if they have the same function. When connecting this product to another product, refer to the supplied manuals of both products and connect cords that have the same
function.
Red
To electric terminal controlled by ignition switch (12
V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
With a 2 speaker system, do not connect anything to the speaker leads that are not connected to speakers.
Perform these connections when using the optional amplifier.
+ | White | Gray | + |
|
| ||
Front speaker |
|
|
|
≠ | White/black | Gray/black | ≠ |
Left |
| ||
|
|
| |
+ | Green | Violet | + |
|
| ||
Rear speaker |
|
|
|
≠ | Green/black | Violet/black | ≠ |
|
| ||
+ |
|
| + |
Rear speaker |
|
|
|
≠ |
|
| ≠ |
+ |
|
| + |
Subwoofer |
|
|
|
≠ |
|
| ≠ |
Front speaker
Right
Rear speaker
Rear speaker
Subwoofer
Fig. 2