Pioneer DJ Controller Serato DJ Edition Connections and part names, Connecting the input/output terminals, Front panel, Rear panel, 8En, cord, cable, (p.21), on page, Portable, Computer, terminals

Connections and part names

!Wait until all connections between devices have been completed before connecting the AC adapter.

Be sure to turn off the power and unplug the AC adapter from the power outlet before making or changing connections between devices.

Refer to the operating instructions for the component to be connected.!Only use the AC adapter included with this unit.!Power to this unit is supplied by the AC adapter or by USB bus power.

This unit can be used by connecting it to a computer using a USB cable, even without connecting the AC adapter.

!Connect this unit and the computer directly using the included USB cable.!A USB hub cannot be used.Notes on running this unit with USB bus power

!When using this unit on USB bus power, supply power to the con- nected computer from the AC power supply. Do not run the com- puter on its battery.

!In cases like the ones below, the power may be insufficient and this unit may not operate on USB bus power.

—When the computer’s USB power supply capacity is insufficient.—When other USB devices are connected to the computer.

If this unit does not operate on USB bus power, connect the included AC adapter.

!The following limitations apply when operating on USB bus power:—The jog dial indicator will not light.—The [MASTER OUT 1] (XLR output) channel is not output.—The [MIC1], [MIC2] and [AUX IN] terminals cannot be used.

—The indicators are dimmer than when using the AC adapter. To use the unit without these limitations, connect the included AC adapter.

Connecting the input/output terminals

Front panel

Headphones	Microphone
To headphones		To microphone
Headphones		Microphone
Headphones		cable
cord		cable
cord
	MIC/AUXTHRU
PHONES	OFF ON	MIC 2

1 2 3

1PHONES jacksConnect headphones here.

Both stereo phone plugs (Ø 6.3 mm) and stereo mini phone plugs (Ø 3.5 mm) can be used.

For details, see Monitoring sound with headphones on page 18.

!There are two input jacks, both a stereo phones jack and a mini phones jack, but do not use both simultaneously. If both are used simultaneously, when one is disconnected and/or connected, the volume of the other may increase or decrease suddenly.

8En

2MIC/AUX THRU selector switchSet this to [ON] if you want to output the [MIC2] and [AUX] channels directly.=Outputting the microphone and AUX sound directly (p.21)3MIC2 terminalConnects a microphone here.=Using a microphone (p.21)

Rear panel

PortablePower speaker, etcaudio device

To audio input	To audio output
terminals	terminals

	1GND	R	L	R	L
	1GND	2 HOT
		3 COLD
-12 dB -6 dB 0 dB R	L	R	L R			L	MIN MAX
-12 dB -6 dB 0 dB R	L	R	L R			L
MASTER ATT.	MASTER OUT1	MASTER OUT2		AUX IN			VOL
1	2	3		4			5
MASTER ATT. MASTER OUT 1 MASTER OUT2 AUX IN	VOL						USB ON OFF DC IN

To power outletComputerAC adapter (included)

5 V

USB	ON OFF DC IN

6 7 8 9 a

1MASTER ATT.Sets the attenuation level of the sound output from the [MASTER1] terminal.2MASTER OUT 1 terminalsConnect powered speakers, etc., here.3MASTER OUT 2 terminalsConnect to a power amplifier, etc.4AUX IN terminal

Connect to the output terminal of an external device (sampler, portable audio device, etc.)

5VOL controlAdjusts the audio level input to the [AUX IN] terminals.6Kensington security slot7 USB terminalConnect to a computer.

!Connect this unit and the computer directly using the included USB cable.

!A USB hub cannot be used.