Pioneer DJM-1000 Other Troubleshooting, Symptom Possible Cause Countermeasure

OTHER (TROUBLESHOOTING)

TROUBLESHOOTING

Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this component, check the points below. Sometimes the trouble may originate from another component. Thus, also check the other electrical appli- ances also in use.

If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service center.

Symptom	Possible Cause		Countermeasure
Power does not turn on.	÷ The power cord has not been connected.	÷ Connect the cord to a power outlet.
Little or no sound.	÷ Input selector switch is in the wrong	÷ Choose the device currently playing with the
	position.		input selector switch.
	÷ Connection cable hasn’t been connected	÷	Connect properly.
	properly or has been disconnected.
	÷ Connector or plug is dirty.	÷	Clean and reconnect.
	÷ MASTER ATT. dial on rear panel is set	÷ Adjust the setting of the MASTER ATT. dial
	too low ([–12 dB], etc.).		in the rear panel.
Sound is distorted.	÷ Master output level is too high.	÷ Adjust the MASTER ATT. dial in the rear
			panel.
	÷ Input level is too high.	÷ Adjust the TRIM dial so that the input level
			approaches 0 dB on the CHANNEL LEVEL
			indicators.
Cannot cross fade.	÷ The setting of the CROSS FADER ASSIGN	÷ Set the CROSS FADER ASSIGN switch of the
	switch ([A], [THRU], [B]) is incorrect.		channel desired to cross fade properly.
Cannot fader start the CD player.	÷ The fader start switch is set to OFF.	÷ Set the fader start switch to ON.
	÷ The rear panel’s player CONTROL	÷ Use the control cable to connect the unit and
	connector hasn’t been connected.		CD player.
External effector’s sound is	÷ The input level from the external effector	÷ Lower the external effector’s output level, or
distorted.	is too high.		adjust the return level using the RETURN
			dial (LEVEL).
External effector doesn’t operate.	÷ The SEND/RETURN button is turned OFF.	÷ Turn the SEND/RETURN button ON.
	÷ The effector is not connected to the	÷ Connect the effector to either the SEND/
	RETURN connector or EFX connector		RETURN connector or the EFX 1 or EFX 2
	located in the rear panel.		connectors in the rear panel.
	÷ The SEND channel selector switch setting	÷ Select the source to which you want to
	is mistaken.		apply effects with the SEND channel selector
			switch.
Link function doesn’t work.	÷ A device supporting digital link is not	÷ Use a digital link cable to connect the DJM-
	connected to the digital link connectors		1000 to a supported device.
	(EFX 1, EFX 2, SOUND 1, SOUND 2,
	VISUAL) in the rear panel.

Static electricity or other external interference may cause the unit to malfunction. To restore normal operation, turn the power off and then on again.

Check the following items if the link connection is not established properly:

CAUTION Indicators	Meaning	Countermeasure
Each link indicator flashes twice.	Unsupported components are connected at	Check the connections at the link input/output
	the link input/output connectors.	connectors.
Each link indicator flashes three	The link connectors of a single DJM-1000	Check connections.
times.	are connected together, or the link
	connectors from two DJM-1000s are
	connected together.
Each link indicator flashes four	Communication error occurred at the link	Check connections and connector cables.
times.	input/output connectors.

16