NAME AND FUNCTION OF PARTS
1Main Microphone Terminal and Microphone
Control Knob
MIC Level:
Used for adjusting the volume of the main microphone. (Attenuated level
HI:
Used for adjusting the high tone of the microphone sound.
Flat at center click.
Increases when rotated to the right. (To +12 dB at 10 kHz) Decreases when rotated to the left. (To
MID:
Used for adjusting the middle tone of the microphone sound.
Flat at center click.
Increases when rotated to the right. (To +12 dB at 1 kHz) Decreases when rotated to the left. (To
LOW:
Used for adjusting the low tone of the microphone sound. Flat at center click.
Increases when rotated to the right. (To +12 dB at 100 Hz) Decreases when rotated to the left. (To
2CH1 to CH4 Input Selection Switch and Control
Knob/Peak level meter
Input selection switch:
Selects which sound of the two units connected to each CH to use.
CH1 : Switches between CD1/LINE and LINE
CH2 : Switches between CD2/LINE and PHONO 1
CH3 : Switches between LINE and PHONO 2
CH4 : Switches between SUB MIC and PHONO 3
TRIM:
Used for adjusting the level of the input signal.
The level increases when rotated to the right. (To +6 dB) The level decreases when rotated to the left. (To
HI:
Used for adjusting the high tone. Flat at center click.
Increases when rotated to the right. (To +12 dB at 10 kHz) Decreases when rotated to the left. (To
MID:
Used for adjusting the middle tone. Flat at center click.
Increases when rotated to the right. (To +12 dB at 1 kHz) Decreases when rotated to the left. (To
LOW:
Used for adjusting the low tone. Flat at center click.
Increases when rotated to the right. (To +12 dB at 100 Hz) Decreases when rotated to the left. (To
Peak level meter:
Displays the peak level holding it for two seconds. Displays the level before channel fader.
The display range is about
When BPM is selected using the effect selector and the effect switch is turned on, the beat monitor function will be turned on.
3Master Output Monaural/Stereo Selection Switch (MONO/STEREO)
4Master level meter (MASTER LEVEL)
Displays the output level after master volume adjusment while holding it for 2 seconds.
The display range is
5Power Supply Switch (POWER)
6BPM Display (Refer to Page 14.)
• When BPM is selected using the effect selector, the BPM of the source selected with the monitor selector (CH1 to CH4) will be displayed.
1 to 4:
Displays the channel measuring the BPM.
Counter:
Displays the BPM value.
The counter displays the measured BPM value.
It will be displayed blinking. If it could not be measured for more than 5 seconds, “– –
(When AVERAGE is selected.)
The display changes when it could be measured. While measuring, the previous value will remain dis- played.
•When other than BPM is selected using the effect selec- tor (DELAY, ECHO, AUTO PAN, FLANGER), the source BPM selected using the effect channel selector (() is con- verted to hours and displayed on the counter.
7Effector Parameter/BPM Display (Refer to Page 14.)
1 to 4 MIC MASTER: Displays the effect source.
Counter:
Displays the effect source BPM and effect parameter, etc. (Refer to ) for details of the parameter.)
BPM...375 to 857 mSec (1 mSec step) 70.0 to 160.0 BPM (0.1 BPM step)
BEAT:
When the effect is set to delay, echo, auto pan, or flanger, displays to which beat the parameter is set. (1/2 to 4 beats)
8Monitor Selector/Auto BPM Counter Selector button (MONITOR SELECTOR/AUTO BPM COUNTER SE-
LECTOR)
•Selects the source which is monitored using the headphone (CH1 to 4, MIC, MASTER, EFFECT).
When several buttons are pressed, sounds can be mixed. When the button is pressed another time, the selection is canceled.
•When BPM is selected using the effect selector, the chan- nel displaying the BPM (CH1 to CH4) is selected.
When more than two are selected together, BPM will not be displayed properly.
9
<DRB1192>
