Pioneer DJM-750 Changing the settings, About the auto standby function, About the talk over function, Setting preferences, settings the Changing

Changing the settings

1Press the [SETUP (WAKE UP)] button for over 1 second.

The [USER SETUP] screen is displayed.

!To display the [CLUB SETUP] screen, first turn this unit’s power off, then press the [POWER] button while pressing the [SETUP (WAKE UP)] button.

2 Press the [BEAT c, d] button.

Select the setting item.

3 Press the [TAP] button.

The screen switches to the setting item’s setting value change screen.

4 Press the [BEAT c, d] button.

Change the setting value.

5 Press the [TAP] button.

Enter the setting value.

The previous screen reappears.

!To return to the previous screen without changing the settings, press the [AUTO/TAP] button.

6 Press the [SETUP (WAKE UP)] button.

Close the [USER SETUP] screen.

!To close the [CLUB SETUP] screen, press the [POWER] button to turn this unit’s power off.

About the auto standby function

When [Auto Standby] is set to [ON], the standby mode is set automatically if 4 hours pass with all of the conditions shown below met.

—That none of this unit’s buttons or controls are operated.

—That no audio signals of –10 dB or greater are input to this unit’s input terminals.

!When the [SETUP (WAKE UP)] button is pressed, the standby mode is canceled.

!This unit is shipped with the auto standby function turned on. If you do not want to use the auto standby function, set [Auto Standby] to [OFF].

About the talk over function

The talk over function has the two modes described below.

—[ADV] (advanced talk over): The mid-range only of the sound of chan- nels other than the [MIC] channel is attenuated according to the [Talk Over LEVEL] setting value and output.

dB

settings the Changing

Frequency

— [NOR] (normal talk over): The sound of channels other than the [MIC]

channel is attenuated according to the [Talk Over LEVEL] setting value and output.

dB

Frequency

Setting preferences

*: Setting upon purchase
Mode	Options settings	Screen display	Setting value	Descriptions
	MIDI CH	MIDI CH	1* to 16	Sets the MIDI channel.
	MIDI Button Type	MIDI BT	TGL*, TRG	Selects the MIDI signal transmission mode, [TGL (TOGGLE)] or [TRG
				(TRIGGER)].
USER SETUP
	Talk Over Mode	TLK MOD	ADV*, NOR	Selects the talk over function’s mode, [ADV(ADVANCED)] or
				[NOR(NORMAL)].
	Talk Over LEVEL	TLK LVL	–6 dB, –12 dB,	Sets the talk over function’s sound attenuation level.
			–18 dB*, –24 dB
	Digital Master Out	DOUT LV	–19 dB*, –15 dB,	Sets the maximum level of the sound output from the [DIGITAL MASTER
	Level		–10 dB, –5 dB	OUT] terminals. 1
	Digital Master Out	DOUT FS	48 kHz, 96 kHz*	Sets the digital signal’s sampling rate.
	Sampling Rate
	MASTER ATT.	MST ATT	–6 dB, –3 dB, 0 dB*	Sets the attenuation level of the sound output from the [MASTER1] and
				[MASTER2] terminals.
CLUB SETUP	Auto Standby	AUTOSTB	ON*, OFF	Turns the auto standby function on and off.
	Mic Output To Booth	MIC BTH	ON*, OFF	Sets whether or not to output the microphone’s audio signals from [BOOTH]
	Monitor			terminals.
	Peak Limiter	PKLIMIT	ON*, OFF	Lessens sudden, unpleasant digital clipping of the master output.
	PC UTILITY	PC UTLY	ON*, OFF	Sets whether or not to launch the computer’s setting utility software auto-
				matically when a USB cable is connected.
	Factory Reset	INITIAL	YES, NO*	Restores all the settings to their factory defaults.

1Note that the output sound may be distorted even if the master level indicator does not light up to the very top.

En 21