Pioneer HTZ363DVD, HTZ767DVD Getting started, Using the on-screen displays, Press SHIFT+MCACC

Getting started 02

•Make sure the mic and speakers are not moved during the MCACC setup.

• If the noise level is too high, NOISY blinks

in the display for five seconds. To exit and

check the noise levels1, press

English

STANDBY		TUNER	SOUND
/ON	DVD/CD	(FM/AM)	RETRIEVER
	USB	LINE	OPEN/CLOSE
			PLAYLIST
1	2	3	1
	AUDIO	SUBTITLE
4	5	6	2
	ANGLE	ZOOM
7	8	9	3

CLEAR	DISPLAY
	0		TV CONTROL		SLEEP
TOPMENU	TUNE	MENU
			INPUT CHANNEL	VOLUME	MUTE
SETUP		SR
ST	ENTER	ST	SHIFT	VOLUME
HOME
MENU		RETURN
MCACC	TUNE	TESTTONE
F.S.SURR	SURROUND ADVANCED	SOUND

SHIFT+MCACC, or to try again, press

ENTER when RETRY shows in the display.

• If you see an ERR MIC or ERR SP message

in the display, there may be a problem with

your mic or the speaker connections. To try

again, press ENTER when you see RETRY2.

Deutsch

1Connect the microphone to the MCACC MIC jack on the rear panel.

	ANTENNA		CR/
		COMPONENT	PR
		VIDEO
		VIDEO	CB/
AM LOOP	FM		PB
	UNBAL 75 Ω
	IN	S-VIDEO	Y
	MCACC	VIDEO OUT
HDMI OUT SETUP MIC CONTROL

When the MCACC setup is complete, the volume level returns to normal and

COMPLETE3 shows in the display, indicating that the MCACC setup is complete and

Acoustic Calibration EQ has been activated.4

Français

2Place the microphone at your normal listening position.

Place it about ear height, and make sure it is level by using a table or chair.

Make sure there are no obstacles between the speakers and the microphone.

3If the system is off, press STANDBY/ON to turn the power on.

If the tuner is selected, switch the input source.

4 Press SHIFT+MCACC.

Try to be as quiet as possible after pressing SHIFT+MCACC. The volume increases automatically and the system outputs a series of test tones.

•Press SHIFT+MCACC to cancel and revert to the previous Auto MCACC settings.

Using the on-screen displays

For ease of use, this system makes extensive use of graphical on-screen displays (OSDs).

All the screens are navigated in basically the same way, using , , , to change the highlighted item and pressing ENTER to select

it.5

Important

•Throughout this manual, ‘Select’ means use the cursor buttons to highlight an item on-screen, then press ENTER.

Button What it does

HOME Displays/exits the on-screen display

MENU

Changes the highlighted menu item

ENTER Selects the highlighted menu item

Italiano Nederlands Español

Note

1• If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.

•Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during the Auto MCACC setup.

2If this doesn’t work, press SHIFT+MCACC, turn off the power, and check the problem indicated by the error message, then try the Auto MCACC setup again.

3If COMPLETE doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.

4See Listening with Acoustic Calibration EQ on page 16 to switch on/off Acoustic Calibration EQ.

5The screen saver will appear after five minutes of inactivity.

11

En