|
|
| Additional Information |
|
|
|
|
|
|
|
|
|
|
|
|
Symptom |
| Cause | Remedy |
|
|
|
|
Broadcast stations cannot be selected | • | Weak radio signals. | • Connect an outdoor antenna (refer |
automatically. |
|
| to page 8). |
|
|
|
|
No sound from surround or center | • | Speaker settings are incorrect. | • Refer to “SPEAKER setting mode” |
speakers. |
|
| on page 17 to check the speaker |
| • | The rear and/or center levels are | settings. |
| • Refer to “Setting the volume level | ||
|
| turned down. | of each channel” on page 21 to |
| • | The surround and/or center | check the speaker levels. |
| • Connect the speakers (refer to | ||
|
| speakers are disconnected. | page 13). |
|
|
|
|
Sound is produced from other | • | SIGNAL SELECT is set incorrectly. | • Set SIGNAL SELECT to ”DIGITAL” or |
components, but not from LD or DVD |
|
| ”ANALOG” according to the type of |
player. | • | The digital inputs are assigned | connections made (refer to page 29). |
| • Set the digital input settings | ||
|
| incorrectly, or not at all. | correctly (refer to page 16, 20, 21). |
|
|
| |
No sound is output or a noise is | • SIGNAL SELECT is set to | • Make digital connections (refer to | |
output when software with DTS is |
| “ANALOG”. | page 11) and set SIGNAL SELECT |
played back. | • A DVD player not compatible with | to “DIGITAL” (refer to page 29). | |
| • Refer to the instruction manual | ||
|
| DTS is used, or the setting of the | supplied with the DVD player. |
|
| DVD player is incorrect. |
|
| • The digital output level is adjusted | • Set the digital volume level of the | |
|
| on a CD player or other component | player to full, or to the neutral |
|
| equipped with digital output level | position. |
|
| adjustment capability. (The DTS |
|
|
| signal has been altered by the |
|
|
| player, and cannot be read.) |
|
|
|
|
|
The sound is output intermittently | • | The overload indicator is lighting | • Set the ADVANCED THEATER |
when software with DTS is played |
| (refer to page 24). | mode to STANDARD (refer to page |
back. |
|
| 32). |
|
|
|
|
When a search is performed by a | • | The search function performed by | • This is not a malfunction, but be |
DTS compatible CD player during |
| the player slightly alters the digital | sure to turn the volume down to |
playback, noise is output. |
| information, making it unreadable. | prevent the output of loud noise |
|
|
| from your speakers. |
|
|
|
|
Cannot be remote controlled. | • | The remote control batteries have | • Replace the batteries (refer to page 6). |
|
| worn out. |
|
| • Too far away or bad angle of | • Operate within 23 feet (7 m), 30° of | |
|
| operation. | the remote sensor on the front |
| • There is an obstacle between the | panel (refer to page 7). | |
| • Remove the obstacle or operate | ||
|
| receiver and the remote control. | from another position. |
| • Strong light such as fluorescent | • Avoid exposing the remote sensor | |
|
| light is shining onto the unit's | on the front panel to direct light. |
|
| remote control signal light- |
|
|
| receiving window. |
|
| • A cord is connected to the | • Connect cord to the correct jack. | |
|
| CONTROL IN terminal on this unit. |
|
|
|
|
|
The display is dark. | • | The FL DIMMER button is pushed. | • Press FL DIMMER on the remote |
|
|
| control repeatedly to return to the |
|
|
| default. |
If the unit does not operate normally due to external effects such as static electricity
Disconnect the power plug from the outlet and insert again to return to normal operating conditions.
55
<ARB7181>