Pioneer VSX-521-K 08Additional information, Resetting the main unit, Cleaning the unit

08Additional information

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver into standby.

2While holding down BAND, press and hold  STANDBY/ON for about two seconds.

3When you see RESET? appear in the display, press AUTO SURROUND/STREAM DIRECT.

OK? shows in the display.

4Press ALC/STANDARD SURR to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default settings.

Cleaning the unit

•Use a polishing cloth or dry cloth to wipe off dust and dirt.

•When the surface is dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleansers.

•Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surface.

Specifications

Amplifier section

Continuous average power output of 80 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than 0.08 %** total harmonic distortion.

Front (stereo) . . . . . . . . . . . . . . . . . . . . . . . . . . 80 W + 80 W Power output (1 kHz, 8 Ω, 0.05 %) . . . . . . .110 W per channel Guaranteed speaker impedance . . . . . . . . . . . . . . 6 Ω to 16 Ω

*Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Output Claims for Amplifiers

**Measured by Audio Spectrum Analyzer

Audio Section

Input (Sensitivity/Impedance)

LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 mV/47 kΩ Output (Level/Impedance)

REC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 kΩ Signal-to-Noise Ratio (IHF, short circuited, A network)

LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98 dB Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]

LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 dB

Video Section

Signal level

Composite . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Vp-p (75 Ω) Component Video . . . . . . . . . . . . . . . . . . . Y: 1.0 Vp-p (75 Ω)

PB, PR: 0.7 Vp-p (75 Ω)

Corresponding maximum resolution

Component Video . . . . . . . . . . . . . . . . . . . . . .1080p (1125p)

Tuner Section

Frequency Range (FM) . . . . . . . . . . . . . .87.5 MHz to 108 MHz Antenna Input (FM). . . . . . . . . . . . . . . . . . . . 75 Ω unbalanced Frequency Range (AM) . . . . . . . . . . . . . . .530 kHz to 1700 kHz Antenna (AM) . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna

Digital In/Out Section

HDMI terminal. . . . . . . . . . . . . . . . . . . . . . . . . . Type A (19-pin) HDMI output type . . . . . . . . . . . . . . . . . . . . . . . . . 5 V, 100 mA ADAPTER PORT terminal . . . . . . . . . . . . . . . . . . . 5 V, 100 mA

Miscellaneous

Power Requirements. . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 W In standby . . . . . . . . . . . . . . . . . . . . . . . 0.4 W (Control OFF) Dimensions . . . . .435 mm (W) x 168 mm (H) x 362.5 mm (D) 173/16 in. (W) x 65/8 in. (H) x 145/16 in. (D)

Weight (without package). . . . . . . . . . . . . . 9.0 kg (19 lb 14 oz)

Furnished Parts

Microphone (for Auto MCACC setup) . . . . . . . . . . . . . . . . . . 1 Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Dry cell batteries (AAA size IEC R03). . . . . . . . . . . . . . . . . . . 2 AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 These operating instructions

Note

•Specifications and the design are subject to possible modifications without notice, due to improvements.

38

En