|
|
|
| Troubleshooting | |
|
|
|
|
|
|
| Check the following guide for the possible cause of a problem before contacting service. | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| Symptom | Cause | Correction | |
|
|
|
|
|
|
|
| DVD or VCR do not | ● DVD or VCR button is not switched | ● Refer to page 6. | |
|
| work properly. | |||
|
| properly. |
|
| |
|
| No power. | ● The power cord is disconnected. | ● Plug the power cord into the wall outlet | |
|
|
| securely. |
| |
|
|
|
| ||
|
| The power is on, but the | ● No disc is inserted. | ● Insert a disc. | |
|
| DVD player does not |
|
| |
|
|
|
|
| |
|
| work. |
|
|
|
|
|
|
|
|
|
|
| No picture. | ● The TV is not set to receive DVD signal | ● Select the appropriate video input mode on |
|
|
|
| output. | the TV so the picture from the DVD player | |
|
|
| appears on the TV screen. | ||
|
|
|
| ||
|
|
|
|
|
|
|
|
| ● The video cable is not connected securely. | ● Connect the video cable into the jacks | |
|
|
| securely. | ||
|
|
|
| ||
|
|
|
|
|
|
|
| No sound. | ● The equipment connected with the audio | ● Select the correct input mode of the audio | |
|
| cable is not set to receive DVD signal | |||
|
| receiver so you can listen to the sound from | |||
|
|
| |||
|
|
| output. | ||
|
|
| the DVD player. |
| |
|
|
|
| ||
|
|
| ● The audio cables are not connected | ● Connect the audio cable into the jacks | |
|
|
| securely. | securely. | |
|
|
|
|
|
|
|
|
| ● The power of the equipment connected | ● Turn on the equipment connected with the | |
|
|
| with the audio cable is turned off. | audio cable. | |
|
|
| ● The Digital Audio Output is set to the | ● Set the Digital Audio Output to the | |
|
|
| correct position, then turn on the DVD | ||
|
|
| wrong position. | ||
|
|
| player again by pressing POWER. | ||
|
|
|
| ||
|
|
|
|
|
|
|
| The picture is poor. | ● The disc is dirty. | ● Clean the disc. | |
|
| ● The TV channels are not tuned in properly. | ● Check tuning, carry out tuning again. | ||
|
|
| |||
|
|
|
|
|
|
|
| The DVD player does not | ● An unplayable disc is inserted. | ● Insert a playable disc. (Check the disc type | |
|
|
| and Regional code.) |
| |
|
| start playback. |
| ||
|
| ● The disc is placed upside down. | ● Place the disc with the playback side down. | ||
|
|
| |||
|
|
|
|
|
|
|
|
| ● The disc is not placed within the guide. | ● Place the disc on the disc tray correctly inside | |
|
|
|
| the guide. | |
|
|
|
|
|
|
|
|
| ● The disc is dirty. | ● Clean the disc. |
|
|
|
| ● The Rating level is set. | ● Cancel the Rating function or change the | |
|
|
|
| rating level. |
|
|
| The remote control does | ● There is an obstacle in the path of the | ● Remove the obstacle. | |
|
| not work properly. | remote control and this unit. |
|
|
|
|
| ● The batteries in the remote control are | ● Replace the batteries with new ones. | |
|
|
| exhausted. |
|
|
|
|
|
|
|
|
|
| Video tape cannot be | ● Is the cassette compartment empty? | ● Eject the tape in. | |
|
| inserted. |
|
|
|
|
|
|
|
|
|
|
| No | ● Audio mode is not set properly. | ● Switch ‘AUDIO’ in the main menu to | |
|
|
| ‘STEREO’. | ||
|
|
|
| ||
|
|
|
|
| |
|
| No NICAM sound | ● NICAM mode is not set properly. | ● Make sure NICAM in the menu is set to | |
|
| recording |
| AUTO for the station to be recorded. | |
|
|
|
|
|
|
English
37
