NOTE: If the engine sounds as if it is try- ing to start before the 5th pull, stop pulling and immediately proceed to the next step.

6.Push the choke knob in completely (to the OFF position); pull the starter rope until the engine starts.

CHOKE (SIDE VIEW)

back toward the front handle as far as possible.

SWhen cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Choke knob OFF FULL

7.Allow the engine to run for approximately 5 seconds. Then, squeeze and release throttletrigger to allow engineto returnto idle speed.

STARTING A WARM ENGINE:

1.Move ON/STOP switch to the ON posi- tion.

2.Push the choke knob in completely (to the OFF position).

3.Slowly press primer bulb 6 times.

4.Squeeze and hold throttle trigger. With thumb press fast idle lock down; then re- lease throttle trigger.

5.Sharply pull the starter rope with your right hand until the engine starts.

6.Squeeze and release throttle trigger to allow engine to return to idle speed.

DIFFICULT STARTING (or starting a flooded engine):

The engine may be flooded with too much fuel if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel by following the warm engine starting procedure listed above. Insure the ON/ STOP switch is in the ON position. Starting could require pulling the starter rope handle many times depending on how badly the unit is flooded. If engine fails to start, refer to the TROUBLESHOOTING TABLE or call 1-800-554-6723.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brakeis triggered.With a broken brake band, the chain brake will not stop the chain. The chain brake should be replaced by an autho- rized service dealer if any part is worn to less than 0.020! (0.5 mm) thick. Repairs on a chain brake should be made by an autho- rized service dealer. Take your unit to the place of purchase if purchased from a ser- vicing dealer, or to the nearest authorized master service dealer.

SThis saw is equipped with a chain brake. The brake is designed to stop the chain if

kickback occurs.

S The inertia--activated chain brake is activated if the front hand guard is pushed forward, either manually (by hand) or automatically (by sudden movement).

S If the brake is already activated, it is disengaged by pulling the front handguard

Braking function control CAUTION: The chain brake must be

checked several times daily. The engine must be running when performing this proce- dure. This is the only instance when the saw should be placed on the ground with the en- gine running.

Place the saw on firm ground. Grip the rear handle with your right hand and the front han- dle with your left hand. Apply full throttle by fully depressing the throttle trigger. Activate the chain brake by turning your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop immediately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Grip the rear handle with your right hand and the front handle with your left hand. Hold the chain saw approximately 14! (35 cm) above a stump or other wooden surface. Release your grip on the front handle and use the weight of the saw to let the top of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

IMPORTANT POINTS

SCheck chain tension before first use and after 1 minute of operation. See CHAIN

TENSION in the ASSEMBLY section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and repair or re-

place parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain

and thus increase the possibility of kickback.

SPractice cutting a few small logs using the following techniques to get the “feel” of us- ing your saw before you begin a major sawing operation.

S Squeeze the throttle trigger and allow the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the en- tire time you are cutting.

10

Page 9 Page 11
Page 10
Image 10
Poulan 2050WT Starting a Warm Engine, Difficult Starting or starting a flooded engine, Inertia activating function control
Page 9 Page 11

2050WT specifications

The Poulan 2050WT is a robust chainsaw designed for both professional and amateur users seeking a reliable tool for tackling various cutting tasks. This model stands out in its class due to its powerful engine, thoughtful design, and advanced features that enhance user experience and efficiency.

At the heart of the Poulan 2050WT is a powerful 50cc two-stroke engine, which provides ample power for felling trees, limbing, and bucking logs. This engine is engineered for performance and reliability, ensuring that the saw can handle demanding tasks without compromising operational effectiveness. The 20-inch bar and chain length offer an optimal balance between cutting capacity and maneuverability, making it suitable for both small and medium-sized cutting jobs.

One of the noteworthy features of the Poulan 2050WT is its ergonomic design, which includes a comfortable grip and lightweight build. This design allows for prolonged usage without causing excessive fatigue, making it an excellent choice for prolonged projects. The chainsaw also incorporates anti-vibration technology, which minimizes the vibrations felt by the operator. This technology not only enhances comfort but also helps in maintaining accuracy during cuts.

Safety is a significant consideration in the design of the Poulan 2050WT. It features a chain brake that can be activated manually, providing an additional layer of safety by stopping the chain immediately in case of kickback. The inertia-activated chain brake further ensures that users are protected during unexpected movements, making this chainsaw a safe option for both inexperienced and experienced users.

Another key feature of the Poulan 2050WT is its easy-start system, which simplifies ignition. The system allows for quick startups with minimal effort, overcoming one of the common challenges faced by chainsaw users. Additionally, the adjustable oil pump allows for customized lubrication settings, ensuring that the chain receives the appropriate amount of oil based on the cutting conditions.

The Poulan 2050WT is also known for its durability and ease of maintenance. Its air filter is user-friendly, ensuring that cleaning and replacement can be done quickly. The tool-less chain tensioning system makes it easier to keep the chain at the optimal tension, reducing downtime and improving overall efficiency.

In summary, the Poulan 2050WT combines power, comfort, and safety features into one effective chainsaw. Whether for household tasks or professional use, this chainsaw offers reliability and performance, making it a solid choice for anyone in need of a dependable cutting tool.
Top Page Image Contents