Poulan 2050WT Fueling Engine, BAR and Chain Lubrication, Important Points to Remember

WARNING: Remove fuel cap slowly when refueling.

FUELING ENGINE

This engine is certified to operate on un- leaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1ratio is obtained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Includedwith this saw is a 3.2 ounce contain- er of oil. Pour the entire contents of this con- tainer into 1 gallon of gasoline to achieve the proper fuel mixture.

DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thorough- ly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri- cation. Lubrication is provided by the auto- matic oiler system when the oil tank is kept filled. Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/ or discoloration of the bar.

In freezing weather oil will thicken, making it necessary to thin bar and chain oil with a small amount (5 to 10%) of #1 Diesel Fuel or kerosene. Bar and chain oil must be free flowing for the oil system to pump enough oil for adequate lubrication.

GenuinePoulanR bar and chain oil is recom- mended to protect your unit against exces- sive wear from heat and friction. PoulanR oil resists high temperature thinning. If Pou- lanR bar and chain oil is not available, use a good grade SAE 30 oil.

SNever use waste oil for bar and chain lubri-

cation.

SAlways stop the engine before removing the oil cap.

IMPORTANT

Experience indicates that alcohol--blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for addi- tional information.

WARNING: The chain must not move when the engine runs at idle speed. If the chain moves at idle speed refer to CAR- BURETOR ADJUSTMENT within this manual. Avoid contact with the muffler. A hot muffler can cause serious burns.

To stop the engine move the ON/STOP switch to the STOP position.

To start the engine hold the saw firmly on the ground as illustrated. Make sure the chain is free to turn without contacting any object.

Use only 15”--18” of rope per pull.

Hold saw firmly while pulling starter rope.

Starter rope handle

Left hand

on front handle

Right foot through rear handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the full extent of the rope as this can cause the rope to break. Do not let starter rope snap back. Hold the handle and let the rope re- wind slowly.

NOTE: Do not attempt to cut material with the fast idle lock button in the locked position.

STARTING A COLD ENGINE (or warm engine after running out of fuel)

ON/STOP SWITCH

(SIDE VIEW)

ON

STOP

1.Move ON/STOP switch to the ON posi- tion.

2.Pull choke knob out to the full extent.

3.Slowly press primer bulb 6 times.

4.Squeeze and hold throttle trigger. With thumb press fast idle lock down; then re- lease throttle trigger.

Fast idle lock button

Throttle

lock--out

Throttle	Choke knob
trigger

5.Sharply pull the starter rope handle 5 times with your right hand. Then, pro- ceed to the next step.

9