Loop Handle LH, Loop Handle RH, Lower Handle

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP10527ES (96192002000)

HANDLES

5 5

KEY	PART	DESCRIPTION	4
NO.	NO.	DESCRIPTION
1	419798X479	LOOP HANDLE LH	2
2	419799X479	LOOP HANDLE RH	2
2	419799X479	LOOP HANDLE RH
3	74780524	SCREW 5/16−18 X 1.50
4	74780528	SCREW 5/16−18 X 1.75
5	751153	NUT 5/16−18

01.08.004-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	419797X479	LOWER HANDLE
2	405784X479	PIVOT SUPPORT WELDMENT
3	17490508	SCREW 5/16−18 X .50
4	17000616	SCREW 3/8−16 X 1.00

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 26

Page 26

Image 26

Poulan PP10527ES, 96192002000, 420923 owner manual Loop Handle LH, Loop Handle RH, Lower Handle, Pivot Support Weldment

Contents

Rev 1 08.08.08 SBW/TH Model NumberSnow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Remove plastic tie securing rod to lower handle Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Auger control lever used to engage auger motion throw snow Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Distance the snow is thrown HOW to USE Your Snow Thrower Stopping To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Release the auger control lever and shut off the engine Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing Plug 420496X421 420495X421Auger 27 LH Auger 27 RH Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley Pivot Lower Handle Loop Handle LHLoop Handle RH Pivot Support Weldment Knob RED SpacerRetainer Handle Knob Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD Bottom Headlight Bezel Wire HarnessConsole Panel Flood Headlight Repair Parts Snow Thrower - Model Number PP10527ES Drive END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PAN 01.03.002-A 409346X428 Frame KEY Part Description ENGINE, TECModel LH358SA-159628A 417014X428 Engine Mount Plate Impeller Belt Belt CoverTraction Belt Repair Parts Snow Thrower - Model Number PP10527ES Wheels Cable Bracket LH Cable Bracket RH Wheel Lobe CoverWheel Driver Retainer Ring Clutch Slide Safety Ignition KEY 35062 DECAL, Poulan PRO DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, Danger Service Notes Limited Warranty

Poulan PP10527ES, 420923 Loop Handle LH, Loop Handle RH, Lower Handle, Pivot Support Weldment

Models: PP10527ES 420923 96192002000

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP10527ES (96192002000)

HANDLES

KEY

LOOP HANDLE LH

LOOP HANDLE RH

KEY

LOWER HANDLE

PIVOT SUPPORT WELDMENT