LEVER/CABLE Rotator Assembly, Rotator Head

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP10527ES (96192002000)

CONTROL PANEL / CHUTE

KEY	PART	*6
KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	420337	LEVER/CABLE ROTATOR ASSEMBLY
2	17501010	SCREW 10−24 X .625
*3	420678	ROTATOR HEAD	*4	01.09.007-A
*4	420677	ROTATOR PIVOT BRACKET	*4		*5


*5	420675	PULLEY PIVOT
*6	420674	CABLE ASSEMBLY

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

01.15.005-A

KEY	PART	DESCRIPTION
NO.	NO.	DESCRIPTION
1	188303	STEER CABLE
2	74041024	SCREW 10−24 X 1.50

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 25

Page 25

Image 25

Poulan 420923, 96192002000 LEVER/CABLE Rotator Assembly, Rotator Head, Rotator Pivot Bracket, Pulley Pivot, Steer Cable

Contents

Snow Thrower Model NumberRev 1 08.08.08 SBW/TH Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONParts Packed Separately in Carton Remove Snow Thrower from Carton Unfold Upper Handle Install Speed Control ROD See FigsRemove plastic tie securing rod to lower handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See Figs Check Tire Pressure Install Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEY Deflector remote control lever used to change Meets A.N.S.I. Safety RequirementsAuger control lever used to engage auger motion throw snow Distance the snow is thrown Stopping HOW to USE Your Snow Thrower Power Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig Release the auger control lever and shut off the engine Before Starting the Engine To Adjust Skid Plates See FigCheck Engine OIL Level See Fig ADD Gasoline See Fig To Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has Frozen General Recommendations MaintenanceBefore Each USE Lubrication Engine Cleaning To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See Fig To Replace Belts See Fig Other Storage Troubleshooting Exploded KEY Part Description Scraper BAR Auger HousingAuger Bearing Bearing Plug Auger 27 LH 420495X421420496X421 Auger 27 RH Chute Weldment Deflector Control AssemblyDeflector Weldment Deflector Seal Rotator Head LEVER/CABLE Rotator AssemblyRotator Pivot Bracket Pulley Pivot Loop Handle RH Loop Handle LHLower Handle Pivot Support Weldment Retainer SpacerKnob RED Handle Knob Traction ROD Assembly Impeller ROD AssemblyShifter ROD TOP Shifter ROD Bottom Console Panel Wire HarnessHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number PP10527ES Drive Drive Plate Assembly Speed Selector AssemblyEND Plate Bottom PAN 01.03.002-A Model LH358SA-159628A KEY Part Description ENGINE, TEC409346X428 Frame 417014X428 Engine Mount Plate Traction Belt Belt CoverImpeller Belt Cable Bracket LH Cable Bracket RH Repair Parts Snow Thrower - Model Number PP10527ES Wheels Wheel Driver Retainer Ring CoverWheel Lobe Clutch Slide 35062 Safety Ignition KEY DECAL, Danger 181037DECAL, Poulan PRO DECAL, DANGER, Deflector DECAL, Danger Service Notes Limited Warranty

Poulan 420923 LEVER/CABLE Rotator Assembly, Rotator Head, Rotator Pivot Bracket, Pulley Pivot

Models: PP10527ES 420923 96192002000

KEY

LEVER/CABLE ROTATOR ASSEMBLY

ROTATOR HEAD

ROTATOR PIVOT BRACKET

PULLEY PIVOT

KEY

STEER CABLE