Install Auger Control ROD See Figs | Poulan 96192002000, 420923

ASSEMBLY / PRE-OPERATION

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

AUGER

CONTROL

ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

	AUGER CONTROL ROD	AUGER
	RETAINER	CONTROL
	RETAINER	LEVER
	SPRING	LEVER
	SPRING
		AUGER
	CONTROL
	BRACKET

FIG. 6

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If neces- sary, rotatechute assembly to align square and pin on un- derside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE
ROTATER		3/8 LOCKNUT
HEAD
		3/8 WASHER
		PIN
		THREADED
		STUD
	ALIGN BEFORE	ROTATER HEAD
CHUTE	ALIGN BEFORE	MOUNTING
BRACKET	TIGHTENING LOCKNUT	BRACKET

FIG. 7

6

Image 6

Poulan 96192002000, 420923 Install Auger Control ROD See Figs, Install Discharge Chute / Chute Rotater Head See Fig

Contents

Model Number Snow ThrowerRev 1 08.08.08 SBW/TH Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from Carton Install Speed Control ROD See Figs Unfold Upper HandleRemove plastic tie securing rod to lower handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEY Auger control lever used to engage auger motion throw snow Meets A.N.S.I. Safety RequirementsDeflector remote control lever used to change Distance the snow is thrown HOW to USE Your Snow Thrower Stopping To Throw Snow See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig Release the auger control lever and shut off the engine Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine ADD Gasoline See Fig Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has Frozen Before Each USE MaintenanceGeneral Recommendations Lubrication Cleaning Engine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Exploded KEY Part Description Auger Bearing Auger HousingScraper BAR Bearing Plug 420496X421 420495X421Auger 27 LH Auger 27 RH Deflector Weldment Deflector Control AssemblyChute Weldment Deflector Seal Rotator Pivot Bracket LEVER/CABLE Rotator AssemblyRotator Head Pulley Pivot Lower Handle Loop Handle LHLoop Handle RH Pivot Support Weldment Knob RED SpacerRetainer Handle Knob Shifter ROD TOP Impeller ROD AssemblyTraction ROD Assembly Shifter ROD Bottom Headlight Bezel Wire HarnessConsole Panel Flood Headlight Repair Parts Snow Thrower - Model Number PP10527ES Drive END Plate Speed Selector AssemblyDrive Plate Assembly Bottom PAN 01.03.002-A 409346X428 Frame KEY Part Description ENGINE, TECModel LH358SA-159628A 417014X428 Engine Mount Plate Belt Cover Traction BeltImpeller Belt Repair Parts Snow Thrower - Model Number PP10527ES Wheels Cable Bracket LH Cable Bracket RH Wheel Lobe CoverWheel Driver Retainer Ring Clutch Slide Safety Ignition KEY 35062 DECAL, Poulan PRO DECAL, DANGER, Deflector 181037DECAL, Danger DECAL, Danger Service Notes Limited Warranty