01.03.002-A | Poulan PP10527ES, 96192002000, 420923 specification

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP10527ES (96192002000)

DRIVE

	7
1b	4
8	3
	3
1b
7	1a
	1a

			KEY	PART	DESCRIPTION
		2	NO.	NO.	DESCRIPTION
		2	1	404923	AXLE ASSEMBLY (assy of 1a,1b)
			1	404923	AXLE ASSEMBLY (assy of 1a,1b)
5	3		1a	404307	AXLE SHAFT
5			1b	9465M1	ROLL PIN 3/16 X 1.50
	4		1b	9465M1	ROLL PIN 3/16 X 1.50
	4		2	402691	SPROCKET
6	01.03.002-A		3	174697	THRUST WASHER
			4	179830	BEARING
			5	146315	SCREW 5/16−18 X .625
			6	17490508	SCREW 5/16−18 X .500
			7	155443	KLIK PIN 1/4 X 1.50
			8	189282	SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Page 32

Image 32

Poulan PP10527ES, 96192002000, 420923 owner manual 01.03.002-A

Contents

Rev 1 08.08.08 SBW/TH Model NumberSnow Thrower Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerParts Packed Separately in Carton Remove Snow Thrower from Carton Remove plastic tie securing rod to lower handle Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See Fig Install Chute Deflector Remote Control See Figs Check Tire Pressure Operation Know Your Snow ThrowerPrimer Ignition KEY Meets A.N.S.I. Safety Requirements Deflector remote control lever used to changeAuger control lever used to engage auger motion throw snow Distance the snow is thrown HOW to USE Your Snow Thrower Stopping Using the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Throw Snow See Fig Release the auger control lever and shut off the engine To Adjust Skid Plates See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See Fig Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has Frozen Maintenance General RecommendationsBefore Each USE Lubrication Cleaning Engine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See Fig To Replace Belts See Fig Storage Other Troubleshooting Exploded KEY Part Description Auger Housing Scraper BARAuger Bearing Bearing Plug 420495X421 Auger 27 LH420496X421 Auger 27 RH Deflector Control Assembly Chute WeldmentDeflector Weldment Deflector Seal LEVER/CABLE Rotator Assembly Rotator HeadRotator Pivot Bracket Pulley Pivot Loop Handle LH Loop Handle RHLower Handle Pivot Support Weldment Spacer RetainerKnob RED Handle Knob Impeller ROD Assembly Traction ROD AssemblyShifter ROD TOP Shifter ROD Bottom Wire Harness Console PanelHeadlight Bezel Flood Headlight Repair Parts Snow Thrower - Model Number PP10527ES Drive Speed Selector Assembly Drive Plate AssemblyEND Plate Bottom PAN 01.03.002-A KEY Part Description ENGINE, TEC Model LH358SA-159628A409346X428 Frame 417014X428 Engine Mount Plate Impeller Belt Belt CoverTraction Belt Repair Parts Snow Thrower - Model Number PP10527ES Wheels Cable Bracket LH Cable Bracket RH Cover Wheel Driver Retainer RingWheel Lobe Clutch Slide Safety Ignition KEY 35062 181037 DECAL, DangerDECAL, Poulan PRO DECAL, DANGER, Deflector DECAL, Danger Service Notes Limited Warranty