6.Disconnect front links from deck by removing retainer springs.

7.Raise lift lever to raise suspension arms. Slide mower out from under trac-

tor.

IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links.

TO INSTALL MOWER

1.Raise attachment lift lever to its highest position.

2.Slide mower under tractor with deflec- tor shield to right side of tractor.

3.Lower lift lever to its lowest position.

4.Connect front links to mower deck and secure with retainer springs.

5.Connect suspension arms to rear deck brackets and secure with retainer springs.

6.Connect anti-sway bar to chassis bracket and secure with retainer spring.

7.Install belt into electric clutch pulley groove.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift

link adjustment nut on that side. NOTE: Each full turn of adjustment nut will change mower height about 1/8".

• Recheck measurements after adjusting.

Bottom edge of

Bottom edge of

mower to ground

mower to ground

 

00598

A

Ground Line

A

Suspension Arm

01553

Lift Link Adjustment Nut

FRONT-TO-BACK ADJUSTMENT

IMPORTANT: Deck must be level side-to side. If the following front-to-back adjustment is necessary, be sure to adjust both front links equally so mower will stay level side-to-side. To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of trac- tor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjust- ments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2"

lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal num- ber of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

01268

Mandrel

“D” “D”

21

Page 20 Page 22
Page 21
Image 21
Poulan CO18542STA manual To Install Mower, To Level Mower Housing, SIDE-TO-SIDE Adjustment, FRONT-TO-BACK Adjustment
Page 20 Page 22

CO18542STA specifications

The Poulan CO18542STA is a robust and efficient lawn mower designed for homeowners seeking a reliable solution for their lawn care needs. This model stands out due to its combination of power, ease of use, and advanced features, making it suitable for various lawn sizes and terrains.

At the heart of the Poulan CO18542STA is a high-performance engine, which provides ample power for cutting through dense grass and challenging conditions. The engine is engineered for durability and efficiency, allowing users to tackle larger areas without frequent refueling. This model features a wide cutting deck measuring 18 inches, which means less time spent mowing and more time enjoying your outdoor space. The cutting height can be easily adjusted, allowing users to customize their lawn care routine according to the season and grass type.

One of the key technologies embedded in this mower is its innovative cutting system. The CO18542STA is equipped with a dual-blade design, which enhances cutting performance and improves grass clippings discharge. This system ensures a clean cut, promoting healthy grass growth and a visually appealing lawn. Additionally, the mower's lightweight construction allows for enhanced maneuverability, ensuring it can navigate around obstacles and tight corners with ease.

The Poulan CO18542STA also emphasizes user comfort and convenience. Its ergonomic handles are designed for optimal comfort during long mowing sessions, reducing fatigue and promoting ease of operation. The mower includes a convenient starting system that allows for quick and easy ignition, minimizing downtime between tasks.

Maintenance is straightforward with the Poulan CO18542STA, thanks to its easy-access engine components and removable cutting deck. This feature enables users to perform routine maintenance tasks without hassle, ensuring the mower remains in peak operating condition.

For those seeking an environmentally friendly option, the Poulan CO18542STA runs on clean-burning, efficient fuel technology. This reduces emissions and aligns with modern sustainability practices, making it a responsible choice for eco-conscious homeowners.

Overall, the Poulan CO18542STA offers an impressive blend of power, technology, and user-focused features. Whether you have a small garden or a more extensive landscape, this mower is designed to deliver reliable performance and ease of use, ensuring your lawn stays healthy and well-maintained year-round.
Top Page Image Contents