BELT INSTALLATION -

1.Carefully work new belt down between transaxle belt keepers and onto the input pulley.

2.Slide belt into the center span keeper.

3.Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

4.Install belt through stationary idler and clutching idler.

5.Reinstall clutch locator and tighten nut securely.

6.Reconnect clutch harness.

7.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

8.Install mower (See “TO INSTALL MOWER” in this section of manual).

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.

Block up axle securely.

2.

Remove axle cover, retaining ring and

 

washers to allow wheel removal (rear

Electric

Clutch

Clutching

Idler

Stationary Idler

Center Span Keeper

Transaxle Pulley

 

Clutch

 

Locator

 

Clutch

 

Wire

01516

Harness

wheels have a square key - Do not lose).

3. Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Retaining Washers

TRANSAXLE GEAR SHIFT LEVER NEU- TRAL ADJUSTMENT

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

1.Make sure transaxle is in neutral (N). NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

2.Loosen adjustment bolt in front of the right rear wheel.

3.Position the gear shift lever in the neu- tral (N) position.

4.Tighten adjustment bolt securely. NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

Gearshift Lever

02239

Neutral

Adjustment Bolt Lock Gate

Ring

Axle

 

Cover

 

Square Key

00663

(Rear Wheel Only)

 

TO START ENGINE WITH A WEAK BATTERY

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

23

Page 23
Image 23
Poulan CO18542STA manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs

CO18542STA specifications

The Poulan CO18542STA is a robust and efficient lawn mower designed for homeowners seeking a reliable solution for their lawn care needs. This model stands out due to its combination of power, ease of use, and advanced features, making it suitable for various lawn sizes and terrains.

At the heart of the Poulan CO18542STA is a high-performance engine, which provides ample power for cutting through dense grass and challenging conditions. The engine is engineered for durability and efficiency, allowing users to tackle larger areas without frequent refueling. This model features a wide cutting deck measuring 18 inches, which means less time spent mowing and more time enjoying your outdoor space. The cutting height can be easily adjusted, allowing users to customize their lawn care routine according to the season and grass type.

One of the key technologies embedded in this mower is its innovative cutting system. The CO18542STA is equipped with a dual-blade design, which enhances cutting performance and improves grass clippings discharge. This system ensures a clean cut, promoting healthy grass growth and a visually appealing lawn. Additionally, the mower's lightweight construction allows for enhanced maneuverability, ensuring it can navigate around obstacles and tight corners with ease.

The Poulan CO18542STA also emphasizes user comfort and convenience. Its ergonomic handles are designed for optimal comfort during long mowing sessions, reducing fatigue and promoting ease of operation. The mower includes a convenient starting system that allows for quick and easy ignition, minimizing downtime between tasks.

Maintenance is straightforward with the Poulan CO18542STA, thanks to its easy-access engine components and removable cutting deck. This feature enables users to perform routine maintenance tasks without hassle, ensuring the mower remains in peak operating condition.

For those seeking an environmentally friendly option, the Poulan CO18542STA runs on clean-burning, efficient fuel technology. This reduces emissions and aligns with modern sustainability practices, making it a responsible choice for eco-conscious homeowners.

Overall, the Poulan CO18542STA offers an impressive blend of power, technology, and user-focused features. Whether you have a small garden or a more extensive landscape, this mower is designed to deliver reliable performance and ease of use, ensuring your lawn stays healthy and well-maintained year-round.