MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the brake pedal is fully depressed and attachement clutch control is in the disengaged position.

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 11)

Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

Remove blade bolt by turning counterclockwise.

Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

BLADE

MANDREL

 

ASSEMBLY

 

CENTER

 

HOLE

BLADE BOLT (SPECIAL)

STAR

FIG. 11

TO SHARPEN BLADE (See Fig. 12)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An un- balanced blade will cause excessive vibration and eventual damage to mower and engine.

The blade can be sharpened with a file or on a grind- ing wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

 

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 12

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

Keep small vent holes open.

Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

17

Page 17
Image 17
Poulan POGT20T48STA manual Tractor

POGT20T48STA specifications

The Poulan POGT20T48STA is a powerful and versatile outdoor tool built for robust performance and efficiency. Designed specifically for tackling tough lawn care tasks, this model blends advanced technology with user-friendly features, making it a top choice for both homeowners and landscaping professionals alike.

One of the standout features of the Poulan POGT20T48STA is its powerful engine. Equipped with a reliable 20-volt lithium-ion battery, this tool provides ample power for longer runtimes, enabling users to work through larger areas without the need for frequent recharging. This battery technology not only enhances the efficiency of the tool but also ensures consistent performance under various environmental conditions.

The design of the POGT20T48STA prioritizes ergonomics and ease of use. It features an adjustable handle that allows users to find their most comfortable working position, reducing fatigue during longer sessions. Additionally, the lightweight construction makes it easy to maneuver, whether you’re trimming grass along sidewalks or tackling tougher brush.

Visibility is also optimized with an integrated LED light, ensuring that you can see your work area clearly, even in low light conditions. This feature is particularly beneficial for early morning or late evening tasks, enhancing safety as well.

The Poulan POGT20T48STA incorporates innovative cutting technology that improves efficiency. The cutting blade is designed for precision, allowing for clean and effective cuts with every pass. Furthermore, the tool boasts multiple cutting height adjustments, providing flexibility for users to customize their mowing experience based on grass type and personal preference.

Durability is a hallmark of the Poulan brand, and the POGT20T48STA is no exception. Crafted from high-quality materials, this tool is designed to withstand the rigors of outdoor use, ensuring longevity and reliability.

In summary, the Poulan POGT20T48STA is an impressive outdoor tool that combines power, efficiency, and user-focused design. With its robust battery technology, ergonomic features, and durable construction, it stands out in the competitive landscape of lawn care equipment. Whether for routine maintenance or more demanding tasks, this tool is engineered to meet the needs of any user looking to achieve a beautifully manicured lawn.