HYDRAULICS

!WARNING

Leaking high pressure fluids can inject themselves under the skin of persons near a leak, creating grave medical risks. TAKE CARE TO AVOID EXPOSURE TO HIGH PRESSURE FLUIDS.

1 . Hydraulic components should be kept as clean as possible during assembly operations.

2.Galvanized pipe and pipe fittings must not be used because flaking or galvanizing material can cause damage to major hydraulic components.

3.A pipe joint sealant, compatible with hydraulic oil, must be applied to all screwed fittings. (Teflon tape is not recommended.)

4.Hose should be protected where severe wear may be caused by vibration or sliding movement.

5.Long runs of hose should be supported by tie wiring or clamping.

6.Pressure and return hoses, connected to hydraulic motors, may be reversed for proper motor rotation. Spinner rotates in a clockwise direction when looking down from top.

7.Use hose manufacturer’s recommendations for fitting re-useable hose ends.

8.Hydraulic pumps must be mounted so shaft rotates in direction of arrow.

9.Locate reservoir as close to pump as possible. It may be installed on truck frame or truck box.

10.Hydraulic return line filter is screwed directly onto reservoir with cartridge down. Oil must flow through filter in direction of arrow on filter.

11.Install the quick connect couplings so that when disconnected, there is a male and female on the truck as well as on the spreader. This way, hoses will always be hooked up properly. and hose ends can be coupled together when spreader is in storage to prevent system contamination.

12.See page 11 for valve assembly

13.Operate hydraulic system for several minutes to warm up. Check all connections for leaks.

14.After running, refill reservoir to three fourths full.

CONTROL AND HYDRAULIC SYSTEM SPECIFICATIONS

*Hydraulic Oil

Good Grade of MS10W Hydraulic Oil Which has

 

wear, oxidation and foam inhibitors.

*Oil Filter

10 Micron Element Return Line Filter.

*Relief Valve Setting1500 PSI

 

*Oil Flow

0 - 10 GPM - With single flow valve connect

 

conveyor and spinner with dual flow valve.

*Oil Flow

0 - 15 GPM - With dual flow valve connect separate

 

pressure line to conveyor and spinner motor.

10

Page 9 Page 11
Page 10
Image 10
Power Acoustik M-940, M-944, M-1044 instruction manual Hydraulics, Control and Hydraulic System Specifications
Page 9 Page 11

M-1044, M-940, M-944 specifications

Power Acoustik is known for its innovation in the mobile audio industry, and their line of amplifiers, including the M-940, M-944, and M-1044, exemplifies this commitment to performance and quality. These amplifiers are engineered to deliver superior sound quality, remarkable power handling, and advanced features that cater to audiophiles and casual listeners alike.

The Power Acoustik M-940 is a robust 4-channel amplifier designed to boost your audio setup. With a peak power output of 940 watts, this amplifier is perfect for driving high-performance speakers, ensuring clear sound reproduction and dynamic bass response. The M-940 employs MOSFET power supply technology, which allows for increased efficiency and minimized distortion, resulting in a clean audio signal across all frequency ranges. Additionally, its variable low-pass and high-pass filters provide flexibility in tuning frequencies, making it easier to achieve the desired sound profile for any listening environment.

Stepping up in power and features, the M-944 offers even greater performance with its 4-channel configuration capable of delivering 944 watts of peak power. It shares the same MOSFET technology as the M-940 but includes a built-in crossover network that enables more precise control over sound frequencies. The M-944 is equipped with thermal and short circuit protection to ensure longevity and reliability, making it suitable for extended listening sessions. Its stylish design and compact form factor also allow for easy installation in a variety of vehicle types.

Finally, the Power Acoustik M-1044 is the powerhouse of the trio, catering specifically to those looking for serious bass performance. As a monoblock amplifier, the M-1044 is capable of producing an impressive 1044 watts of peak power specifically tailored for subwoofers. The M-1044 features adjustable bass boost and phase control, enabling users to fine-tune their bass response for maximum impact. Its heavy-duty construction ensures durability, even under demanding conditions.

Each of these amplifiers employs advanced technology to ensure optimal performance. With features such as RCA inputs, variable gain control, and remote bass level adjustments, Power Acoustik amplifiers provide versatility and ease of use. The combination of power handling capabilities, sound clarity, and user-friendly features makes the M-940, M-944, and M-1044 excellent choices for anyone looking to enhance their mobile audio experience. Whether you prefer crystal-clear highs or booming bass, Power Acoustik has an amplifier to meet your audio needs.
Top Page Image Contents