INSTALLATION INSTRUCTION FOR

ELECTRIC THROTTLE CONTROL

!WARNING

1.Disconnect battery, NEGATIVE CABLE (if already installed).

2.Spreaders with factory installed throttle controls do not require installer hook-up to the engine. The actuator has been installed and tested at the factory.

3.Raise the engine shroud and securely prop it in place with the prop rod. The installer will have to remove the ties securing the coiled actuator cable to the top of the engine.

4.The throttle actuator cable plugs into the in-cab control panel after being routed from the cab of the vehicle to the rear of the mounted spreader.

5.Select a suitable location in the cab of the vehicle to mount the throttle control box. (Do not mount at this time.)

!WARNING

Consult vehicle manufacturer for acceptable mounting locations. Improperly mounting the control box could interfere with air bag(s) and the other functions of the occupant protection systems, such as knee bolsters!

6.After the location of the control panel is determined, the cable must be routed to the rear of the spreader, so the hookup can be made with the actuator cable plug. Route the conductor cable, attached to the control, to rear of truck, under truck, securing as needed. Allow enough cable for the control panel to be mounted in the cab.

7.The routed cable must be clear of all moving or hot parts on the spreader or vehicle. Secure the cable with the ties provided. Excess cable must be coiled up and secured.

8.Locate and mount the control panel (with screws supplied).

9.For permanent cable mount at rear of the truck, a mounting bracket is supplied.

10.Slide boot over cable then, wire the control panel cable end into the socket (wire colors and locations are identified on the socket). The rubber socket boot must be installed for weather resistant seal.

11.Fill boot from cable side with a good grade of dielectric grease to help reduce corrosion on terminals.

12.Install a 12 volt battery with 4- ampere hour rating, recommended for winter use (if not already done). The battery hold-downs furnished will accept any 2 SM Series battery.

4

Page 3 Page 5
Page 4
Image 4
Power Acoustik M-940, M-944, M-1044 instruction manual Installation Instruction for Electric Throttle Control
Page 3 Page 5

M-1044, M-940, M-944 specifications

Power Acoustik is known for its innovation in the mobile audio industry, and their line of amplifiers, including the M-940, M-944, and M-1044, exemplifies this commitment to performance and quality. These amplifiers are engineered to deliver superior sound quality, remarkable power handling, and advanced features that cater to audiophiles and casual listeners alike.

The Power Acoustik M-940 is a robust 4-channel amplifier designed to boost your audio setup. With a peak power output of 940 watts, this amplifier is perfect for driving high-performance speakers, ensuring clear sound reproduction and dynamic bass response. The M-940 employs MOSFET power supply technology, which allows for increased efficiency and minimized distortion, resulting in a clean audio signal across all frequency ranges. Additionally, its variable low-pass and high-pass filters provide flexibility in tuning frequencies, making it easier to achieve the desired sound profile for any listening environment.

Stepping up in power and features, the M-944 offers even greater performance with its 4-channel configuration capable of delivering 944 watts of peak power. It shares the same MOSFET technology as the M-940 but includes a built-in crossover network that enables more precise control over sound frequencies. The M-944 is equipped with thermal and short circuit protection to ensure longevity and reliability, making it suitable for extended listening sessions. Its stylish design and compact form factor also allow for easy installation in a variety of vehicle types.

Finally, the Power Acoustik M-1044 is the powerhouse of the trio, catering specifically to those looking for serious bass performance. As a monoblock amplifier, the M-1044 is capable of producing an impressive 1044 watts of peak power specifically tailored for subwoofers. The M-1044 features adjustable bass boost and phase control, enabling users to fine-tune their bass response for maximum impact. Its heavy-duty construction ensures durability, even under demanding conditions.

Each of these amplifiers employs advanced technology to ensure optimal performance. With features such as RCA inputs, variable gain control, and remote bass level adjustments, Power Acoustik amplifiers provide versatility and ease of use. The combination of power handling capabilities, sound clarity, and user-friendly features makes the M-940, M-944, and M-1044 excellent choices for anyone looking to enhance their mobile audio experience. Whether you prefer crystal-clear highs or booming bass, Power Acoustik has an amplifier to meet your audio needs.
Top Page Image Contents