Powerware 30-160kVA

12 Powerware 9315 Maintenance Bypass Module 30-160kVA

164201177 Rev. C 041500

Refer to the following while installing the MBM:

·Dimensions in this manual are in millimeters and (inches).

·Do not tilt the unit more than 10˚during installation.

·Remove the conduit landing plates to add conduit landing holes as required.

Plate material is 16 gauge steel (0.06 in. thick).

·Terminals are UL and CSA rated at 90˚C. A hex key tool is required to attach

wires to the terminals.

·Details about power wiring are provided in the tables of Appendix A of this

manual.

Figure 6 shows typical power wiring terminations of the UPS module and

Maintenance Bypass Module (30---160kVA). Refer to the Powerware 9315

Installation manualprovided with the UPS system for location of UPS module

cabinet wiring terminations.

NOTE: Material and labor for external wiring are to be provided by designated

personnel.

LEFT DOOR

Output

Neutral

Connection

(E12)

TB1

A/C Output

E9, E10,E11

UPS MODULE

MaintenanceBypass Module (30--160kVAUPS Shown)

TB2

RIGHT DOOR

REMOVED

FOR

CLARITY

MBP

MIS

BIB1

BIB2

BREAKERANNUNCIATION

CRITICAL LOAD

CONNECTIONS

NEUTRAL

CONNECTIONS

OPTIONALUPS

BYPASS

INPUTCONNECTIONS

UTILITY INPUT,

IF BIB BREAKER

INSTALLED

UPS/PTC OUTPUT

CONNECTION

UTILITY INPUT,

IF BIB BREAKER

IS NOT

INSTALLED

Figure 6. Typical Power Wiring Terminations of UPS Module and

MaintenanceBypass Module (30 --- 160kVA)

Contents

Main Page Table of Contents 1 Appendix A A--- 1................................................. 2 3 List of Figures Introduction Using This Manual Conventions Used in This Manual For More Information Getting Help United States 1-800-843-9433 Canada 1-800-461-9166 Outside the U.S. Call your local representative Page Getting Started Preparing the Site Creating an Installation Plan Environmental Considerations 1. 2. 3. Preparing for Wiring the Maintenance Bypass Module Inspecting and Unpacking the Maintenance Bypass Module Page Unloading the MBM from the Pallet 1. 2. 3. 4. 6. 7. 8. 9. Installing and Wiring the Maintenance Bypass Module LineandLoadWiring Page Maintenance Bypass Module Operation Preliminary Checks and Startup for UPS Equipped with Maintenance Bypass Module (MBM) Maintenance Bypass Module Operation MBM Operation Without Kirk Key Interlocks From UPS Bypass to Maintenance Bypass: From Maintenance Bypass to UPS Bypass: MBM Operation With Kirk Key Interlocks (Optional) Kirk Key Solenoid Release Unit (SKRU) MBM Transfer Sequences From UPS Bypass to Maintenance Bypass: From Maintenance Bypass to UPS Bypass: Maintenance Short Circuits Maintenance Bypass Module Diagrams Page Appendix A --- Customer Information A --- 2 Table A--1. Ratings & External Wiring Re quirements for Powerware 9315 128 M B M 3 0 --- 1 6 0 A --- 3 Table A--2. Ratings & External Wiring Re quirements for Powereware 9315 128 M B M 3 0 --- 1 6 0 A --- 4 Table A--3. Ratings & External Wiring Re quirements for Powerware 9315 128 M B M 3 0 --- 1 6 0 A --- 5 Table A--4. Rating and External Wiring Requirements for Powerware 9315 M B M 5 0 --- 1 6 0 A --- 6 Table B. Circuit Breaker Req uirements for Powerware 9315 M B M 3 0 --- 1 6 0 480:208VAC, 600:208VAC, 208:208VAC, 480:480VAC. A --- 7 Table B. Circuit Breaker Req uirements for Powerware 9315 A --- 8 Tab l e C - - 1 . P o w e r Ca b l e Te r mi n a t i o n s UPS Figure 1. (Reverse Transfer) Figure 2. (Parallel Redundant) MBM UPS1 Page Page Page 30--- 160kVA UPS System with MBM A --- 1 4 164201177---4 ONELINE -- 30-160kVA, RT, 480:480VAC, 600:600VAC, 400:400VAC A---15 164201177---5 ONELINE -- 30-160kVA, RT, 480:208VAC, 600:208VAC A --- 1 6 164201177---6 ONELINE -- 30-160kVA, RT, 208:208VAC A---17 164201177---7 164201177 Rev. C 041500 ONELINE -- 30-160kVA, PARALLEL, 480:480VAC 600:600VAC, 400:400VAC A --- 1 8 164201177---8 164201177 Rev. C 041500 ONELINE -- 30-160kVA, PARALLEL 480:208VAC, 600:208VAC A---19 164201177---9 ONELINE -- 30-160kVA, PARALLEL, 208:208VAC