Premier Mounts PWM-F110 installation manual Safety Precautions

PWM-F110

Warning Statements

Safety Precautions

This wall mount should be installed by qualified personnel having sufficient skill and competence to install it. Qualified installation specialists or your dealer should install the mount and set up the plasma television in order to avoid personal injury or property damage. Premier Mounts does not assume liability for injury or damage caused by improper installation, mounting or setup of the plasma television, misuse, modification or natural disasters.

The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before beginning installation. The installation instructions should be read, understood and followed to prevent personal injury or property damage. Keep these installation instructions in an easily accessible location for future reference.

The wall being considered for mounting must be capable of supporting at least five (5) times the weight of 40Kg. If it is not, the wall must be reinforced before beginning installation.

Only use specified parts for the installation of the mounting bracket. Do not use the mounting hardware from any other mount or any other source.

A secured structure wooden stud wall must always support the weight or load of the plasma. Always confirm the center of the wood stud before beginning the installation. Failure to do so could result in personal injury and physical damage.

Avoid installing the plasma in locations where temperatures and humidity are excessively high, or contact with any water or vapors possible. This could result in fire, electrical shock and damage to the plasma television. Water will damage the wall structure for wall mount installation. The permissible temperature is (0-40ºC) and humidity is (20%-80%).

The mount is designed to be used on vertical walls only. Do not install near or on doors, angled ceilings, walls, or any other installations other than wall mounting. Failure to do so could result in damage and injury. This wall mount is to be used only with plasma television. Use with any plasma television other than is prohibited and may cause injury and damage.

Make sure the plasma mounting area is completely free of internal or external wires, pipes, gas lines, phone lines etc. Failure to do so will result in injury and damage to the walls, wiring or piping system.

Avoid Installations where there is danger of contact with over excessive dust, oil smoke, and tobacco smoke. Failure to do so may result in fire or damage to the plasma or its internals.

Do not block the ventilation holes. Sufficient clearance must be left in the area surrounding the plasma and wall mount to avoid blocking the vents and causing the plasma to overheat which could cause a risk of fire. Leave 100mm or more away from all of the surrounding four sides for proper airflow.

Do not install in locations where there is vibration, movement or danger of impact. Failure to do so could result in plasma cracking or falling from the wall causing damage and injury.

Do not install near heater, fireplace, direct sunlight or air conditioning or any other source of direct heat energy. Failure to do so may result in damage to the plasma television and could cause a risk of fire.

It is not necessarily to open the plasma television prior to installation. Never open the plasma or modify the mount. This plasma is to be used only as outlined in the installation instruction. Failure to do so may result in damage and injury. If a malfunction or problem occurs, contact the nearest dealer.

At least two qualified people should always perform the installation work. Injury and damage can result from dropping or bending the plasma television.

All six (6) M8 bolts (part B) and quick release sleeves (part A) must be firmly tightened and secured to the plasma television in the correct locations. If the quick release sleeves are not properly installed, do not hang the plasma television to the wall mount. Damage and Injury could result from the plasma falling down.

All four (4) Lag bolts must be properly secured to the 450mm wall studs. The lag bolts must always be secured through the center of the wood studs. Failure to do so could result in the plasma falling from the wall causing damage to the plasma and personal injury.

All bolts must be properly tightened and secured before installing the plasma display. Failure to do so could result in the plasma falling causing damage to the plasma and personal injury.

Objects on the wall may collect dust quicker than anticipated. Check periodically for dust accumulation. Refer to the plasma installation instructions for cleaning instructions.

Do not play around the plasma or throw any objects near or at the screen. The glass screen is very sensitive and may scratch or break or cause the plasma television to fall from the wall causing personal injury and damage.

Page - 4 - Installation Manual