X I . C A R E A N D M A I N T E N A N C E
AXLE BEARINGS AND THE MOTOR/ | DRIVE WHEEL WASHER |
| ||||||
TRANSAXLE ASSEMBLY |
|
| AXLE KEY | |||||
You do not need to lubricate these items, as they are |
|
|
| |||||
all prelubricated and sealed. |
|
|
|
|
|
| ||
MOTOR BRUSHES |
|
|
|
|
|
|
| |
The motor brushes are housed inside of the motor |
|
|
| |||||
transaxle/assembly. | They | should | be | inspected |
|
| AXLE SLOT | |
periodically for wear by your authorized Pride |
|
| ||||||
Provider. |
|
|
|
|
|
|
|
|
WHEEL REPLACEMENT |
|
|
|
|
|
| ||
If your scooter is equipped with pneumatic tires and | DRIVE WHEEL NUT |
| ||||||
you have a flat tire, you can have the tube replaced. |
| |||||||
|
|
| ||||||
If your scooter is equipped with a solid tire insert, |
|
|
| |||||
either the solid insert or the entire wheel must be | Figure 26. Solid Tire Wheel Removal |
| ||||||
replaced depending on the model. Contact your |
|
|
| |||||
authorized Pride Provider for information regarding |
| HUB | ||||||
replacement wheels for your scooter. |
|
|
| |||||
|
|
|
|
| ||||
WARNING! Wheels on your scooter |
| REAR RIM HALF |
| |||||
|
|
| ||||||
should only be serviced/replaced by | WARNING! | COMPLETELY |
| |||||
an authorized Pride Provider or qual- |
| |||||||
DEFLATE THE TIRE BEFORE |
| |||||||
ified technician. |
|
|
| ATTEMPTING REPAIR! |
| |||
WARNING! | Completely |
| deflate |
|
|
| ||
pneumatic tires before dismantling |
|
| TIRE | |||||
the rim or attempting repair. |
|
|
| |||||
WARNING! Be sure that the key is |
|
|
| |||||
removed from the key switch and the |
|
| TUBE | |||||
scooter is not in freewheel mode |
|
| ||||||
before performing this procedure. |
|
|
| |||||
WARNING! When changing a tire, |
|
|
| |||||
remove only the center lug nut, then |
| FRONT RIM HALF | ||||||
remove the wheel. If any further |
| |||||||
disassembly is required, deflate the |
| WASHERS |
| |||||
tire completely or it may explode. |
|
| ||||||
|
|
| ||||||
Follow these easy steps for a quick and safe |
| NUTS |
| |||||
|
|
| ||||||
repair of both pneumatic and solid tires: | Figure 27. Drive Wheel Assembly |
| ||||||
1.Remove the key from the key switch.
2.Elevate the side of the scooter from which you
are removing the tire. Place wooden blocks under the frame to elevate the scooter.
3.If you are changing a pneumatic tire, completely deflate it before removing the wheel.
4.Remove the drive wheel nut and washer from the axle. See figure 26.
5.Pull the wheel off the axle.
6.Remove the nuts and washers and separate the rim halves. See figure 27.
7.Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid tire.
8.Reassemble the rim halves.
9.Slide the wheel back onto the axle. Make sure that the axle key is in the axle slot. See figure 26.
Celebrity X LE | www.pridemobility.com | 39 |
