![](/images/new-backgrounds/1298221/29822121x1.webp)
10. Remove the plastic ties from the Right Handrail | 10 |
|
|
|
|
|
|
|
|
(90) and the Left Handrail (not shown). If neces- |
|
|
| Console Assembly |
|
| |||
sary, press the Cage Nuts (38) into place. |
|
|
|
|
|
| |||
Have a second person hold the console assem- |
|
|
|
|
|
|
|
|
|
bly near the Right Upright (78). |
|
|
|
|
|
|
|
|
|
Connect the Upright Wire (77) to the console |
|
|
|
|
|
|
|
|
|
wire. See the inset drawing. The connectors |
|
|
|
|
|
|
|
|
|
should slide together easily and snap into |
|
|
|
|
|
|
|
|
|
place. If they do not, turn one connector and |
|
|
|
|
|
|
|
|
|
try again. IF THE CONNECTORS ARE NOT |
|
|
|
|
|
|
|
|
|
CONNECTED PROPERLY, THE CONSOLE |
|
| 38 |
|
|
|
|
|
|
MAY BE DAMAGED WHEN THE POWER IS |
|
|
| 90 |
|
|
|
| |
TURNED ON. Remove the long tie from the | Plastic |
|
|
|
|
| |||
Upright Wire and the tie from the console wire. |
| Ties |
| Console | Console |
|
| ||
Then, insert the connectors into the Right Upright |
|
| 77 |
|
| ||||
(78). |
|
|
| Wire |
| Wire |
|
| |
Set the console assembly on the Right Upright |
|
|
|
|
|
|
|
|
|
(78) and the Left Upright (not shown). Make sure |
|
|
| Long |
| 77 |
|
| |
that no wires are pinched. |
| 78 |
|
|
| ||||
|
|
| Tie |
|
|
|
| ||
11. Tighten four M8 x 25mm Bolts (6) with four M8 | 11 |
|
|
|
|
|
|
|
|
Star Washers (10) into the Uprights (73, 78) and |
|
|
|
|
|
|
|
| |
the Handrails (89, 90). Start all four Bolts be- |
|
|
|
|
| 110 |
|
|
|
fore tightening any of them. |
|
|
|
|
| 111 |
|
| |
See steps 4 and 6. Tighten the M10 x 96mm |
|
|
|
|
|
|
|
| |
Bolts (5). |
|
|
| 88 |
|
|
|
|
|
Press the Left Accessory Tray (110) and the |
|
|
|
|
|
|
|
| |
Right Accessory Tray (111) into the Console |
|
|
|
|
|
|
|
|
|
Base (88). | 89 |
|
|
|
|
|
|
| |
|
|
| 6 |
|
|
|
| ||
| 6 | 10 | 10 |
|
|
|
| ||
|
| 73 | 90 |
|
| ||||
|
|
|
|
| 10 | 6 | |||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
| 6 | 10 | 78 | |
|
|
|
|
|
|
|
| ||
| 11 |
|
|
|
|
|
|
|
|