ProForm PFANBE3525.0 user manual Make sure that the Barbell is centered

Models: PFANBE3525.0

1 24
Download 24 pages 54.91 Kb
Page 12
Image 12

20. Orient the Locking Bar (50) as shown. Slide the

20

 

 

 

 

Barbell (51) through the Left Barbell Guide (52),

 

 

 

 

 

 

 

 

 

the Locking Bar, and the Right Barbell Guide (53).

53

 

 

 

 

Make sure that the Barbell is centered in the

 

 

 

 

 

 

 

 

 

Barbell Guides. Engage the Locking Bar into the

50

 

 

 

 

Uprights (43) at the lowest position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hole

 

 

 

43

 

52

 

 

 

 

51

21. Hand tighten an M8 x 20mm Button Screw (16)

21

 

 

 

 

into the Left Barbell Guide (52).

 

 

 

 

 

 

 

 

 

Slide a Weight Stop (69) onto the Barbell (51).

 

 

 

41

Hand tighten an M6 x 15mm Button Screw (17)

 

 

 

 

59

into the Weight Stop. Make sure that the Screw

60

 

 

 

 

 

 

 

is tightened enough to engage the hole (see

 

 

 

 

39

drawing 20) in the Barbell.

 

 

 

 

 

 

 

 

60

 

 

 

 

 

Repeat this step on the other side of the

52

 

 

51

 

Barbell (51).

 

 

 

 

 

 

16

 

 

 

 

 

 

 

Tighten the screws used in this step, and the

43

 

 

17

69

bolts and locknuts used in steps 11–15 and

 

 

 

 

 

17–19.

 

 

 

 

 

Press two Center Base Feet (60) onto the Center

 

 

64

 

 

 

 

 

 

 

Rack Base (39). Press the Rear Upright Foot (59)

 

 

 

 

 

onto the Rear Upright (41). Press two Front

 

 

 

 

 

Upright Feet (64) onto the Front Uprights (43).

22

 

 

 

 

22. Route a Cable (61) up through the Top Frame

 

 

45

 

 

(45) and over a Pulley (63). Attach the Pulley

80

 

 

 

63

 

 

inside the Top Frame with an M10 x 67mm Bolt

 

 

 

 

 

 

 

 

(86), two M10 Washers (80), two 16mm x

77

 

 

 

 

12.5mm Spacers (76), and an M10 Nylon Locknut

 

 

 

 

76

 

 

 

 

(77).

 

 

 

 

 

 

 

 

 

 

61

76

80

 

 

 

 

 

 

 

 

 

 

86

 

 

23. Route the Cable (61) over a Pulley (63) and down

23

 

 

 

 

through the Top Frame (45). Attach the Pulley

 

 

 

 

 

 

 

 

 

inside the Top Frame with an M10 x 67mm Bolt

80

 

63

 

 

(86), two M10 Washers (80), two 16mm x

76

 

 

 

12.5mm Spacers (76), and an M10 Nylon Locknut

 

 

45

 

 

 

 

 

(77).

77

 

 

 

 

 

 

 

 

 

 

 

 

 

 

61

76

80

 

 

 

 

 

 

 

 

 

 

 

 

 

 

86

 

 

12

 

 

 

 

Page 12
Image 12
ProForm PFANBE3525.0 user manual Make sure that the Barbell is centered