See the inset drawing. Tie the wire tie | ProForm PFTL14511.1

3. Identify the Left Upright (89), which is marked	3
with a “Left” sticker or an “L” sticker. Have a sec-	3
with a “Left” sticker or an “L” sticker. Have a sec-
ond person hold the Left Upright near the Base			81
(94).			81
(94).				89
See the inset drawing. Tie the wire tie in the				89
See the inset drawing. Tie the wire tie in the				Wire	81
Left Upright (89) securely around the end of the				Wire	81
Upright Wire (81). Then, pull the other end of the				Tie
wire tie until the Upright Wire is routed through
the Left Upright.			Wire
			Tie
	89
			81	94
				94
4. Hold the Left Upright (89) against the Base (94).	4
Be careful not to pinch the Upright Wire (81).	4
Be careful not to pinch the Upright Wire (81).
Insert two 3/8" x 1 1/4" Screws (8) with two 3/8"				81
Star Washers (13) and two 3/8" x 2 3/4" Screws				81
(7) into the Left Upright.		89
Partially tighten the 3/8" x 2 3/4" Screws (7) and		89
Partially tighten the 3/8" x 2 3/4" Screws (7) and
the 3/8" x 1 1/4" Screws (8) until the heads of the
Screws touch the Left Upright (89); do not fully
tighten the Screws yet. Note: It may be help-
ful to use the Short Hex Key (64) on the Screw
shown.	7
Attach the Right Upright (not shown) in the	7		64
Attach the Right Upright (not shown) in the
same way. Note: There are no wires on the right
side.	13
	13
	8	13	94
		13

	8

Image 8

ProForm PFTL14511.1 user manual See the inset drawing. Tie the wire tie, Be careful not to pinch the Upright Wire

Contents

QUESTIONS? Model No. PFTL14511.1 Serial NoCall TOLL-FREE Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT Table of Contents Important Precautions Page Before YOU Begin Part Identification Chart Assembly Make sure that the power cord is unplugged See the inset drawing. Tie the wire tie Be careful not to pinch the Upright WireTighten the Screws yet. Note It may be help Attach the Right Upright not shown Base Covers into place yet Page Wire. See the inset drawing. The connectors Should slide together easily and snap intoAgain. if YOU do not Connect the CON Then tighten themPage Power cord. Next, see page 17 and turn on PowerWhen the frame stops moving, remove Important See page 15 and plugPage Use a Surge Suppressor Operation and AdjustmentHOW to Connect the Power Cord Console DiagramFeatures of the Console Sole. Important HOW to Turn on the PowerHOW to USE the Touch Screen HOW to SET UP the Console Connect to your wireless network Check for firmware updatesCalibrate the incline system Create an iFit Live account HOW to USE the Manual Mode When you are finished exercising, remove Power cord. Important If you do not doKey from the console Measure your heart rate if desired Start the workout HOW to USE AN Onboard WorkoutSelect an onboard workout HOW to USE a SET-A-GOAL Workout Select the main menu. See on Select a set-a-goal workout HOW to USE AN Ifit Live Workout Start the workout. See on HOW to USE the Equipment Settings Mode HOW to USE the Maintenance Mode Exit the maintenance modeCalibrate the incline system of the treadmill Find keycodes HOW to USE the Wireless Network Mode Enable Wi-FiSet up and manage a wireless network connection Exit the wireless network mode HOW to USE the Stereo Sound System HOW to USE the Internet Browser HOW to Fold and Move the Treadmill HOW to Fold the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USE Troubleshooting Symptom The power turns off during use Symptom The walking belt slows when walked on Top ViewPage Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise Frequency Suggested Stretches Part List Qty Description Description Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty