PYLE Audio PT-690A Basic Operation, Tape Aux Phono, Ana→Opt→Coax, Bstereo, Cpro Logic, Ereset

BASIC OPERATION

BASIC OPERATION 1

POWER

MASTER VOLUME

DOLBY DIGITAL/DTS AV RECEIVER PT-690A

POWER

ONOFF

STANDBY

	WOOFER	DIGITAL	SURROUND	DTS/	INPUT SELECTOR
MUTE	ON/OFF DIMMER	IN	MODE	STEREO PROLOGIC DOLBYDIGITAL
				OPTICAL S-VIDEO VIDEO	L AUDIO R

AV3 IN

PHONES

STANDBY MASTER VOLUME

1.Press the POWER button to ON.

2.Press STANDBY button to switch on the unit.

3.Select the desired source by pushing the corresponding button

DVD (ANA, COAX)

VIDEO 1 (ANA, COAX.)

VIDEO 2 (ANA, OPT.)

VIDEO 3 (ANA, OPT.)

TUNER (FREQUENCY)

TAPE

AUX

PHONO

Note: INPUT MODE is used to select one of the 3 Modes.

ANA→OPT→COAX

When DVD, VIDEO 1 is selected, press the INPUT MODE button and select “ANALOG” or “COAXIAL” in accordance with your connection.

When VIDEO2, VIDEO3 is selected, press the INPUT MODE button and select “ANALOG” or “OPTICAL” in accordance with your connection.

If			appears on the display:
	A	digital input source (OPT or COAX) has been

selected, and the source is connected successfully.

If “ UNLOCK” appeared for 5 seconds on the display: The source is not connected properly or the source is

not switched on.

In that case, connect and switch the source on, or select ANALOG by pressing the INPUT MODE button.

4.Play the source, and gradually turn up the volume to the required level with the MASTER VOLUME control.

BASIC OPERATION 2

APOWER & STANDBY/ON button Press this button to turn the power on. Press it again to turn the system off (power standby mode).

The STANDBY indicator lights up in power standby mode and goes out when this unit is turned on.

BSTEREO

With the unit in the STEREO mode, only Front Left and Front Right Speaker and Woofer have output.

C PRO LOGIC II

Opposed to Dolby Pro logic, which had four channels (front, left, center, and surround) recorded into two channels with matrix processing and then played back in four channels, Dolby Pro Logic II uses a feedback logic circuit to have 5.1-channel surround audio(Dolby Surround, etc.) matrix-encoded into two channels and then played back in its original 5.1-channel form.

There are five standard modes: Movie, Music, Virtual, Pro Logic Emulation, and Matrix.

D SURROUND MODE

This mode is possible to achieve a realistic sound field with a “three dimensional” feel, giving the sense of distance, movement and relative position, and creating a surprisingly real and powerful sense of presence when playing movie software in AV rooms.

There are six surround modes: THEATER, HALL, PASSTHRU, MOVIE, MUSIC, and ROOM.

E RESET

When this unit is ON, use a paper clip to press this button for more than 3 seconds to reset the whole system (including memories).

F PHONES jack

For private listening, insert optional (not included) headphones (1/4-inch plug) into the PHONES jack, and then the center and surround speaker will be cut automatically.

Note: When the headphone is used, the output will down mix to STEREO automatically.

G AV 3 IN

The input ports are for VCR, Video Camera Recorder, etc. It contains one optical, one S-video, one video input port and Analog Left and Right input ports.

H BASS/TREBLE control

BASS control is used to adjust the level of the low frequency sound range.

TREBLE control is used to adjust the level of high frequency sound rang.

Press one of them on the remote control and then press +/- key (26, remote) to adjust the level of them.

15