TEST TONE, LFE TRIMMER AND CHANNEL SELECT.
TEST TONE
Speaker Level balance Adjustment
The test tone function is useful to adjust the relative volume between speakers in DOLBY DIGITAL or DOLBY PRO LOGIC II mode.
Once the balance is set, you don’t have to change the balance as long as the speakers aren’t moved.
1.Adjust the MASTER VOLUME to the normal listening level. (Half of max. Volume is recommended)
2.Press the TEST TONE button (on the remote control) in DTS, Dolby Digital or Dolby PRO LOGIC II
mode.
The test tone is emitted from each speaker each time you press “TEST TONE”.
POWER | MUTE | DELAY | SPK |
|
TIME | SETUP |
| ||
| SU RROU ND |
|
|
|
| MODE | BASS |
|
|
MEMOR Y | DOLBY PL II | TREBLE |
|
|
|
| INPUT | SUBWOOFER |
|
|
| SELECT | ON/OFF |
|
| DOLBY |
| CH |
|
| DIGITAL | DIMMER | SELECT |
|
STATION | DYNAMIC | INPUT | TEST |
|
| MODE | TONE | TEST | |
|
|
|
| |
| BAND |
| LFE TRIM | TONE |
|
|
| ||
| AUTO |
|
|
|
TUNING | MANUAL | TUNING |
|
|
| ST/MONO |
| VOLUME | VOLUME |
|
|
|
→ L(FRONT LEFT)→R (FRONT RIGHT)→LS (SUR. LEFT) → ← SUB ← C (CENTER) ← RS (SUR. RIGHT)
3.Select a speaker by pressing the “TEST TONE” button and adjust the level by pressing the MASTER
VOLUME button.
The level of each speaker can be adjusted in 1 dB step from
4.When the setting is finished, press the TEST TONE button to stop the test tone.
Note: You must keep press TEST TONE until one complete cycle is finished.
LOW FREQUENCY EFFECT (LFE MIX)
LFE (LOW FREQUENCY EFFECT) MIX LEVEL (LFE MIX)
Under COAX./OPT mode, when playing , input AC3 or DTS 5.1CH signal, LFE will appear on the VFD, then press LFE key on the remote, and again press VOL +/- key to adjust the level between 0dB to
Note: The LFE adjust state resume to normal, if MASTER VOLUME is not press after 5 seconds.
POWER | MUTE | DELAY | SPK |
|
TIME | SETUP |
| ||
| SURROUND |
|
|
|
| MODE | BASS |
|
|
MEMORY | DOLBY PL II | TREBLE |
|
|
|
| INPUT | SUBWOOFER |
|
|
| SELECT | ON/OFF |
|
| DOLBY |
| CH |
|
| DIGITAL | DIMMER | SELECT |
|
STATION | DYNAMIC | INPUT | TEST |
|
| MODE | TONE | TEST | |
|
|
|
| |
| BAND |
| LFE TRIM | TONE |
|
| LFE TRIM | ||
|
|
|
| |
| AUTO |
|
|
|
TUNING | MANUAL | TUNING |
|
|
ST/MONO | VOLUME |
| |
|
CHANNEL SELECT
Balancing volume between speakers in 5.1 channel mode when using the 5.1 analogue inputs.
As the Dolby Digital signal is decoded in the external source, sometimes, you may have to balance volume between speakers due to the location of speakers. In this case:
POWER | MUTE | DELAY | SPK |
|
TIME | SETUP |
| ||
| SURROUND |
|
|
|
| MODE | BASS |
|
|
MEMORY | DOLBY PL II | TREBLE |
|
|
|
| INPUT | SUBWOOFER |
|
|
| SELECT | ON/OFF |
|
| DOLBY | DIMMER | CH |
|
| DIGITAL | SELECT | CH | |
|
|
|
| |
STATION |
| INPUT | TEST | SELECT |
| DYNAMIC | MODE | TONE | TEST |
|
|
|
| |
|
|
|
| TONE |
| BAND |
| LFE TRIM |
|
| AUTO |
|
|
|
TUNING | MANUAL | TUNING |
|
|
| ST/MONO |
| VOLUME | VOLUME |
|
|
|
1.Press “CH SELECT” on the remote, the following loop will appear on the display:
→ L(FRONT LEFT)→R (FRONT RIGHT)→LS (SUR. LEFT) → ← SUB ← C (CENTER) ← RS(SUR. RIGHT) ←
2.Adjust the Master Volume to balance all speakers. The level of each speaker can be adjusted in 1 dB steps from
Note:
If the Master Volume is not adjusted for 5 seconds in Channel Trimmer state, it returns to normal state.
20