QSC Audio 8 ohm capable) user manual CX204V, Specifications Subject To Change Without Notice

EN

Specifications 2- and 4-Channel Distributed 70V Line Models

		CX204V	CX302V	CX602V	CX1202V
OUTPUT POWER (Watts)
20 - 20k Hz, 0.03% THD, 70V/Ch.		200	200	400	800
20 - 20k Hz, 0.03% THD, 8 Ohms/Ch.				550	700
20 - 20k Hz, 0.05% THD, 4 Ohms/Ch.					1100
1k Hz, 0.05% THD (EIA), 70V/Ch.		220	250	440	1000
1k Hz, 0.1% THD (EIA), 70V/Ch.			300	600	1200
1k Hz, 1.0% THD (EIA), 70V/Ch.		300
Bridge Mono, 140V, 20 - 20k Hz, 0.1% THD		400	400	800	850
Bridge Mono, 140V, 1k Hz, 0.1% THD		440	600	1200	2400
Bridge Mono, 1k Hz, 0.1% THD, 16 Ohms				1200	1400
Bridge Mono, 1k Hz, 0.1% THD, 8 Ohms					2300
DISTORTION, SMPTE-IM		<0.02%, all models
FREQUENCY RESPONSE		20 - 20k Hz, ±0.2dB at 10dB below rated output power, all models (-3dB points: 8 Hz and 100 kHz)
SIGNAL to NOISE, unweighted, 20 - 20k Hz		-106 dB. all models
VOLTAGE GAIN		56.6x (35dB) all models
INPUT SENSITIVITY, Vrms		1.26V (+4.2dBu) for rated power at 70.7V
OUTPUT CIRCUIT TYPE		AB	AB	AB	H
INPUT IMPEDANCE		6k ohms unbalanced, 12k ohms balanced, all models
DYNAMIC HEADROOM		2 dB at 4 Ohms, all models
DAMPING FACTOR		>500 at 8 Ohms, all models
AMPLIFIER PROTECTION		Short circuit, open circuit, thermal, ultrasonic and RF protection. Stable into reactive or mismatched loads
COOLING		Continuously variable speed fan; back-to-front air flow through heat sink tunnel
CONTROLS	Front:	AC POWER switch, gain controls (1 control per channel, 21 detents)
	Back:	10-position DIP switch with Clip Limiter (1 per Ch.), LF Filter on/off (1 per Ch.)
		LF filter select: 33 or 50 Hz (1 per Ch.), Stereo/Parallel/Bridge mode selection switches
LED INDICATORS		POWER (green, 1 each), SIGNAL, -10dB, -20dB (green, 1 each per Ch.), CLIP (red, 1 each per channel),
		BRDG and PAR (yellow, 1 each)
CONNECTORS	Input:	3-pin terminal blocks ("euro" or "Phoenix" type)and			XLRs (pin 2 positive)
	Output:	barrier strip connectors with protective shroud
	Other:	QSC DataPort connector (supports full “V1”feature set)
LOAD PROTECTION		Turn-on/turnoff muting, AC coupling (DC fault blocking), Clip limiting.
POWER REQUIREMENTS		Refer to rear panel serial number label. Configured at factory for 100, 120 or 220-240 VAC, 50- 60 Hz.
DIMENSIONS		19.0" (48.3 cm) W, 3.5" (8.9 cm) H, 14" (35.6 cm) D (from front mounting rails, including rear support ears)
WEIGHT		21 pounds (9.5 kg) net; 27 pounds (12.3 kg) shipping

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

12