7.DOOR GLASS CLEANING AND REPLACEMENT

A.Be sure the insert is cold before cleaning the glass. To clean the glass, use a damp paper towel or any non-abrasive glass cleaner. Then use a dry towel to wipe off any streaks that may remain.

B.This glass is 5m thick high temperature heat resistant ceramic glass. DO NOT replace it with any other material.

C.Never slam the door or strike the glass in any way, as this may cause breakage. NOTE: The insert will not operate with broken or missing glass. If it becomes necessary to replace the glass, replacement glass is available from your nearest Quadra-Fire dealer.

D.To replace glass:

1.Remove door from insert and lay on a padded flat surface.

2.Remove glass tabs and screws with a Phillips screwdriver by turning screws clockwise.

3.Lift glass frame and glass out of the door frame.

4.Place new glass with fiberglass tape around it into door frame, making sure the Quadra-Fire logo reads correctly to the outside.

5.Place glass frame pieces over the fiberglass tape on the edges of the glass. Be sure glass is centered in the opening (i.e., same space top and bottom, left and right).

6.Reinstall screws and glass tabs tightly enough to hold everything in place.

7.Check again for centering of glass in door frame, and tighten all screws securely.

8. READING THE FIRE AND ADJUSTMENT PROCEDURES

A properly adjusted fire has a short active flame pattern that extends out of the firepot 4" to 6" (100mm to 152mm). If the fire has tall flames with black tails and seems somewhat lazy, the feed rate will need to be reduced. Start adjusting this type of fire by sliding the feed adjustment plate down about 1/2” (13mm). Within eight minutes your adjustment will have taken effect. If the fire is still too tall, lower the feed adjustment plate again. If the fire is still lazy and you have reached the end of adjustment for the feed plate, you will need to increase the combustion air. When the fire is too small and rarely peaks above the top of the firepot, you will need to increase the feed rate by adjusting the plate upwards. If the feed adjustment plate reaches the end of its travel and the fire is still low and very active, you will have to close the air adjustment to achieve a proper flame.

Page 14

Page 13 Page 15
Page 14
Image 14
Quadra-Fire 1100-I owner manual Door Glass Cleaning and Replacement, Reading the Fire and Adjustment Procedures
Page 13 Page 15

1100-I specifications

The Quadra-Fire 1100-I is a renowned wood-burning insert, designed to deliver robust performance and efficiency for homeowners looking to enhance their heating solutions. Known for its sleek finish and effective heating capabilities, this model is an excellent choice for those who want to experience the warmth and ambiance of a traditional wood fire.

One of the standout features of the Quadra-Fire 1100-I is its impressive heating capacity. With the ability to heat spaces up to 2,000 square feet, it makes an ideal option for medium to large homes. This wood insert boasts a nominal output of 65,000 BTUs, providing sufficient warmth even in the coldest winters. Its efficient design allows for long burn times of up to 10 hours, ensuring that you can enjoy continued warmth throughout the night without the need for constant refueling.

A critical technology incorporated in the Quadra-Fire 1100-I is its Advanced Combustion System. This system utilizes a secondary combustion process that minimizes emissions and maximizes efficiency. As the fire burns, it re-burns the gases and particulates that would typically escape into the atmosphere, resulting in a cleaner and more environmentally friendly burn. This feature not only reduces the impact on the environment but also enhances fuel efficiency, saving homeowners money on wood consumption.

The insert features a large ceramic glass door that allows for a captivating view of the fire, adding a cozy and inviting ambiance to any room. The glass is designed to withstand high temperatures without warping or discoloring, ensuring a clear view for years to come. Additionally, the Quadra-Fire 1100-I offers an easy-to-use airflow control system, allowing you to adjust the flame and heat output according to your preferences, making it easy to manage your heating needs throughout the day.

Installation of the Quadra-Fire 1100-I is straightforward, as it is designed to fit into existing fireplaces, eliminating the need for extensive renovations. The unit is also available with several finishing options, allowing homeowners to choose a look that complements their interior design.

In summary, the Quadra-Fire 1100-I is an ideal wood-burning insert for those seeking efficiency, environmental consciousness, and aesthetic appeal. With its powerful heating ability, advanced combustion technology, and striking design, it stands out as a reliable and attractive choice for anyone looking to add a wood-burning solution to their home.
Top Page Image Contents