Manuals / Quadra-Fire / Household Appliance / Indoor Fireplace

Quadra-Fire QVI-35FB-S owner manual B. Mantel and Wall Projections

Models: QVI-35FB-S

1 41

Download 41 pages 18.04 Kb

Page 18

B. Mantel and Wall Projections

B. Mantel and Wall Projections

WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speciﬁed. Framing or ﬁnishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

Clearance to combustible material under the insert is 1/4 inch (6 mm). Clearance to sides of ﬁreplace opening to combustibles is 6 inches (152 mm). Clearance from top of ﬁreplace opening (152 mm) to combustibles extending 1 inch is 6 inches. Clearance from top of ﬁreplace opening for combustibles extending 1 inch to 12 inches max. is 12 inches.

•Use leveling legs to raise insert minimum 1/4 inch (6 mm) above combustible material or outer wrap of factory built ﬁrebox.

Combustible facings must not extend behind the insert surround.

Note: All measurements in inches.

INLET AIR	12 in. MAX.
EXHAUST VENT PIPE
VENT PIPE
	MANTEL

12 in. MIN.

MEASUREMENTS FROM

TOP EDGE OF UNIT

Figure 5.2 Clearances to Mantels or other Combustibles above Appliance

18	Quadra-Fire • QVI-35FB-S • 2178-900 Rev. B • 12/08

Image 18

Quadra-Fire QVI-35FB-S owner manual B. Mantel and Wall Projections

Contents

Model QVI-35FB-S What to do if you smell gasA. Congratulations Homeowner Reference InformationRead this manual before installing or operating this appliance Installer Guide Table of ContentsSafety Alert Key User GuideB. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTYCONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY B. Limited Lifetime Warranty continued A. Appliance Certiﬁcation C. High Altitude Installations1 Listing and Code Approvals B. BTU SpeciﬁcationsA. Gas Fireplace Safety 2 Operating Instructions User GuideB. Your Fireplace C. Clear Space E. Fixed Glass AssemblyF. Remote Controls, Wall Controls and Wall Switches D. Decorative Doors, Fronts and SurroundsTO TURN OFF GAS TO APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS H. Standing Pilot IgnitionISSUE J. Frequently Asked QuestionsI. After Appliance is Lit SOLUTIONSGlass Cleaning 3 Maintenance and ServiceA. Maintenance Tasks-Homeowner Remote ControlLogs B. Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection FireboxFigure 3.1 Standing Pilot Flame Patterns Quadra-Fire QVI-35FB-S 2178-900 Rev. B 12/08Installer Guide Getting StartedA. Typical Appliance System GAS LINE SECTION 9 ACCESS THROUGH EXISTING MASONRYMANTEL LEG SECTIONS 5 SURROUND HEARTH EXTENSION GAS LINE SECTION 9 ACCESS THROUGH EXISTING MASONRYVERTICAL TERMINATION CAP SECTION 8F VENT PIPE SECTION MANTEL AND OR WOODBURNING FIREPLACEB. Design and Installation Considerations C. Tools and Supplies NeededD. Inspect Appliance and Components 5 Fireplace Size Requirements A. Minimum Fireplace OpeningB. Mantel and Wall Projections Fire Risk Maintain vent clearance to combustibles as speciﬁed 6 Termination LocationsA. Vent Termination Minimum Clearances DO NOT pack air space with insulation or other materialsB. Flue Damper 7 Installation PreparationA. Inspection and Cleaning C. Gas LineA. Vent Limits 8 Installing Vent Pipe and ApplianceC. Connecting Vent Pipe B. Venting ComponentsAIR PASSAGE SLIDE PLATE SLIDE PLATE HANDLE #8 SCREW E. Remote ControlD. Placing, Securing and Leveling the Appli- ance SLIDE PLATE BRACKETFactory Built Wood Burning F. Installing Adaptor and Termination CapMasonry CAUTION! Risk of Cuts/Abrasions/Flying DebrisA. Fuel Conversion D. High Altitude Installations9 Gas Information B. Gas PressureA. Wiring Requirements B. Standing Pilot Ignition System Wiring10 Electrical Information C. Junction Box Installation D. Fan ReplacementOptional Accessories GROUND WIRE TEMPERATURE SENSOR SWITCHTEMPERATURE SENSOR SWITCH SPEED CONTROL RHEOSTAT VARIABLE SPEED CONTROL JUNCTION BOX BLKBLK11 Finishing A. Mantel and Wall ProjectionsC. Clean the Appliance 12 Appliance SetupA. Remove Glass Assembly D. AccessoriesLog Set QVI35FB-S Shown Log Set Assembly LOGS-CFXGBF. Install the Log Assembly 4 LOCATING TABS A-DLOG NUMBER 2 SRV768-704 Position log #2 LOG NUMBER 3 SRV768-705 Position log #3Quadra-Fire QVI-35FB-S 2178-900 Rev. B 12/08 Removing Fixed Glass Assembly G. Fixed Glass AssemblyH. Air Shutter Setting Removing Fixed Glass Assemblyshort in electrode wire 13 TroubleshootingA. Standing Pilot Ignition System Check that the pilot ﬂame impinges on the thermocouple. Adjust thee. Wall switch or wires are defective Troubleshooting continuedON/OFF switch in the ON position. Check the millivolt Follow the corrective action in Symptom and PosMODEL DIMENSIONS A. Appliance Dimension Diagram14 Reference Materials LocationB. Vent Kits Components QVI-35FB-S Log Set AssemblyC. Service Parts Part number list on following pageStocked C. Service Parts ListQVI-35FB-S at DepotQVI-35FB-S Service PartsPilot Assembly NG Stockedinstallation and operation D. Contact Informationand maintenance DO NOT DISCARD THIS MANUAL