RAD Data comm ASM-60 View Error Log Screen , Resets Menu

Appendix C IR-IP Interface Module ASM-60 Installation and Operation Manual

C-22 Device Control Menu

View Error Log Screen

This item of the Device Control submenu is used to view the error log file. This file

logs errors detected in IR-IP for debug and technical support purposes.

Resets Menu

The Resets menu allows you to perform reset of IR-IP, or its interfaces.

This operation can be used to restore normal operation after service is disrupted

by an abnormal condition. Any data stored in the IR-IP buffers is discarded, and

the flow of traffic is temporarily interrupted.

➤ To access the Resets menu:

• From t he Device Control menu, type 3.

The following screen appears:

IR_IP <IR-IP> S/W Ver. 1.00 31/IR (date)

Quick Setup

Management Access

Advanced Setup

Device Control

.....................................................................

New Software Download

View error LOG

Resets

=====================================================================

1. Reset Device

2. Reset LAN

3. Reset WAN

Press one of the numbers to select or ESC:

Figure C-18. Resets Menu

Reset Device

➤ To restart IR-IP:

• From t he Resets menu, type 1.

You will be prompted to confirm the reset operation.

Resetting the device will restart the IR-IP interface module, and therefore traffic flow

is temporarily interrupted, and the Telnet connection is lost.

Reset LAN

➤ To reset the LAN interface:

• From t he Resets menu, type 2.

You will be prompted to confirm the reset operation.

This operation restarts the IR-IP LAN controller.

To continue your Telnet session, press any key within 15 seconds following the

confirmation of the reset operation.

Note

Note

Contents

Main ASM-60 10 Mbps VDSL-Based Modem Installation and Operation Manual Notice Page Warranty Limitation of Warranty Exclusive Remedies Safety Warnings Telecommunication Safety Regulatory Information FCC-15 User Information Warning per EN 55022 Quick Start Guide 1. Installing ASM-60 Setting the Internal Switches Connecting the Interfaces Connecting the Power 2. Operating ASM-60 Normal Indications 3. Configuring ASM-60 Selecting the Data Rate Contents List of Figures List of Tables Chapter 1 Introduction 1.1 Overview General Versions Application Page 1.2 Physical Description 1.3 Functional Description 1.4 Technical Specifications Page Chapter 2 Installation and Setup 2.1 Site Requirements and Prerequisites Caution Warning 2.2 Package Contents 2.3 Installation and Setup Caution Performing the Internal Settings Warning Connecting the Interfaces Connecting the Line Connecting the DTE Connecting the Power Page Chapter 3 Operation 3.1 Front Panel Indicators 3.2 Operating ASM-60 Turning On ASM-60 Normal Indications Turning Off ASM-60 Chapter 4 Management from a Terminal 4.1 Preparing for the Control Session Control Port Interface Characteristics Preparing Terminal Control Port Handshaking Protocol 4.2 Navigating the Management Menus Terminal Management Menus 4.3 Starting the Control Session 4.4 Configuring ASM-60 Selecting the Data Rate 4.5 Displaying the ASM-60 System Information Displaying the ASM-60 Status 4.6 Resetting ASM-60 Page Chapter 5 Diagnostics 5.1 Error Detection Power-Up Self-Test Front-Panel LEDs Alarms Working with the Log File Table 5-1. ASM-60 Alarms 5.2 Displaying the VDSL Performance Diagnostics Figure 5-3. VDSL Performance Screen Table 5-2. ASM-60 Performance Monitoring Parameters 5.3 Running the Diagnostic Tests Running the LEDs Test Page Appendix A IR-ETH Interface Module A.1 IR-ETH Connector Options A.2 Technical Specifications General LAN WAN A.3 Installation and Operation DIP Switch Settings LED Indicators Connecting to LAN Appendix B IR-ETH/QH Interface Module B.1 Introduction B.2 IR-ETH/QH Connector B.3 Technical Specifications B.4 Installation and Operation Figure B-3 shows location of the configuration DIP switch on the modules board. Figure B-3. DIP Switch Location Setting the DIP Switch LED Indicators Connecting the LAN Appendix C IR-IP Interface Module C.1 Introduction Overview Application C.2 Technical Specifications Router LAN WAN C.3 Physical Description IR-IP LEDs IR-IP DIP Switch C.4 IR-IP Management Subsystem, General Introduction Accessing the IR-IP Management Subsystem Default IP Communication Parameters C.5 Performing Preliminary Configuration General Outline of Preliminary Configuration Connecting the Telnet Host Preliminary Telnet Host Configuration Assigning the Router LAN Interface Address IP Learning Mechanism Assigning a LAN IP Address to a New IR-IP Changing the LAN IP Address of a Configured IR-IP What to Do If ... C.6 IR-IP Management Utility General Operating Procedures Starting a Management Utility Appendix C IR-IP Interface Module ASM-60 Installation and Operation Manual C-10 Quick Setup Menu C.7 Quick Setup Menu LAN IP Address LAN IP Mask WAN IP Address WAN IP Mask Default Gateway C.8 Management Access Menu Telnet Password Telnet Inactivity Timeout C.9 Advanced Setup Menu Device Identification Menu Device Name Contact Person System Location Interface Parameters Menu LAN Status WAN Status WAN Throttle Aging Timeout WAN Protocol Parameters Frame Relay Protocol Menu Self Learn Maintenance Protocol DLCI CIR WAN Protocol Parameters PPP Protocol Menu Header and Control Field Compression Protocol Field Compression Authentication Protocol Security Host/Guest User Name To Send Password To Send User Name To Accept Password To Accept Multicast IP Menu Multicast Forwarding Static Groups C.10 Device Control Menu New Software Download Menu Server IP Address File Name Total Timeout Start Operation View Error Log Screen Resets Menu Reset Device Reset LAN Reset WAN C.11 View Menu Configuration and Connection ARP Tables Multicast Groups Table Screen Statistics Screen Figure C-24. WAN Statistics Screen C.12 Diagnostic Tool (Ping Terminal) Menu Figure C-25. Diagnostic Tools Menu Using the Ping Function C.13 Erasing Users Configuration C.14 Erasing IR-IP Software Erasing Application Software Downloading New Software