Manuals / Brands / TV and Video / Satellite TV System / Raymarine / TV and Video / Satellite TV System

Raymarine Satellite TV Systems How do I connect the system cables?....

1 78

Download 78 pages, 4.16 Mb

15

How do I connect the system cables?....

Connecting the antenna

Antenna baseplate

There are two types of antenna baseplate that can be fitted to your Rayma-

rine TV System. the types are:

• 2 RF port connectors.

• 4 RF port connectors.

Which type is fitted depends on your area of operation and the antenna

model. The models are:

Raymarine 45STV system

All antennas are fitted with a 2 RF port connector baseplate.

Raymarine 60STV system

Regions with circular polarization

North America, South America (DirecTV) - 2 RF port connectors.

Regions with linear polarization

Europe and Middle East - 4 RF port connectors.

Australia, China, and New Zealand - 2 RF port connectors.

To connect the antenna

1. Pass the power/data cable through the access hole of the mounting

plate and connect it to the power/data connector on the antenna base

plate.

Note:

It is good practice to coat the threads of all connector s with a small

amount of a suitable waterproof marine sealant prio r to securing them.

2. Hand tighten the power/data cable connector. Take care not to over-

tighten the nut, as this will damage the connector.

3. Remove the protective cap from the RF 1 connector.

4. Connect the RF cable to the RF 1 connector and secure using a 13 mm

spanner.Take care not to over-tighten the nut, as this will damage the

connector.

Note:

The base plate connectors must be suitably protected from water in-

gress when the antenna unit is installed on an open structure, e.g. a tuna tower.

RF1

RF2

POWER POWER

RF 2RF 1

RF 4RF 3

2 RF port

connector baseplate

4 RF port

connector baseplate

D9276_1

81258_3.book Page 15 Wednesday, November 8, 2006 2:06 PM

Contents

Main Page Contents Page Safety notices WARNING Product installation In-line fuse Antenna unit cover Page Important information Introduction Geographic location Television reception EMC conformance Declaration of conformity Waste Electrical and Electronic Equipment Directive Restriction of the use of certain Hazardous Substances What does a typical system look like? Satellite receivers, televisions and subscription services must be purchased separately. Page Installation EMC installation guidelines Whats in the box?.... What tools do I need to install my TV system?.... How do I plan the installation?... Cables Power requirements Clear view of sky Extending the cables How do I install the ACU?.... ACU dimensi ons Installing the ACU How do I install the antenna?.... Preparing the antenna Preparing the mount Securing the antenna How do I connect the system cables?.... Connecting the antenna Note: Antenna baseplate Connecting the ACU How do I configure the system?... Systems with 2RF connector baseplate Single IRD In-line fuse Twin IRDs Multiple IRDs North American systems and South America (DirecTV) North American systems - DirecTV Multiswitch MASTER IRD 1 IRD 2 IRD 3 Multi S/W IRD1 Europe, Australia, New Zealand, China, Middle East, South America (Sky) System with 4 RF connector baseplate Single IRD Twin IR Ds Multiple IRDs Systems using up to 4 IRDs Systems using more than 4 IRDs Connecting your satellite TV system to an NMEA0183 GPS * This applies to Raymarine 60 STV systems only. Pin 1 Pin 2 Page System set up Introduction Set up using the ACU Start up Changing the default satellite * Set up mode Setting the satellite pair Setting the satellite pair - DirecTV Setting the GPS using the ACU If your system is connected to a GPS antenna, the position will be updated in real time. Edit satellite information p Note: (1) (2 ) Vertical and horizontal polarization applies to regions with linear polarization only. Setting the local frequency LNB systems in regions with circular polarization Raymarine does not recommend changing the LNB type unless instructed to do so. LNB systems in regions with linear polarization Raymarine does not recommend changing the LNB type unl ess instructed to do so. Setting the DiSEqC method Setting the LNB skew angle This menu is only applicable to Raymarine 60STV Premium models * CALIBRATION - uses the skew sensor motor to position th e LNB. MANUAL- enables you to set the skew angle manually according to signal strength. Display version Setting antenna go position Setting antenna move step Setting defaults Set up using the Graphical User Interface PC GUI main menu Controller menu Antenna status Serial port set up The GUI control soft keys Setting the GPS Editing the satellite information Setting antenna angle, move step and diagnosis. Moving the antenna to a new position Antenna diagnosis Setting the skew angle This section is only applicable to regions with linear polarization. Maintenance and troubleshooting Introduction Maintenance Troubleshooting * for an explanation of possible causes and their remedies refer to the following paragraphs. Page Antenna diagnosis Press EXIT to return to main set up menu. If failed, check the power and data cable connections. Technical support www.raymarine.com Satellite information Introduction Satellite coverage areas Climatic conditions European satellites Page Page Page US satellites Page Australia Optus C1 New Zealand Optus B1 Page Middle East Page South America Satellite coverage by geographic location Europe Page Satellite tracking Satellite service providers European satellites Page North American satellites Australia and New Zealand Far East Page Appendix 7: Technical specification Raymarine 45 STV Page Page Raymarine 60 STV