Manuals / Brands / TV and Video / Satellite TV System / Raymarine / TV and Video / Satellite TV System

Raymarine Satellite TV Systems Europe, Australia, New Zealand, China, Middle East, South America (Sky)

1 78

Download 78 pages, 4.16 Mb

20 Raymarine Satellite TV Systems

• Set the ACU to ON.

• The IRDs to OFF.

• The television receivers to OFF.

6. Confirm that the antenna detects and tracks the DirecTV101 satellite.

7. Set the Master IRD to ON.

8. Set the Master IRD television receiver to ON.

9. Set the remaining IRDs to ON.

10. Set the remaining television receivers to ON.

The system can now be controlled using the Master IRD.

Europe, Australia, New Zealand, China, Middle East, South America (Sky)

In order to connect multiple IRDs to the antenna, you will need to purchase

a suitable universal LNB multiswitch. The multiswitch has to be installed

between the antenna unit and the IRDs as shown in the following diagram.

You should connect to either the vertical or horizontal high and low pairs

depending whether you want to watch channels in the high or low bands.

Only those channels in the selected band will be available for viewing.

To connect three or four IRDs:

1. Connect an RF cable to RF1 and another to RF2 on the antenna base

plate.

2. Connect the RF1 cable to either Lo/Ver or Hi/Ver. This will depend on

whether the desired programming is in the vertical or horizontal low

band.

3. Connect the RF2 cable to:

• Lo/Hor if RF1 was connected to Lo/Ver.

• Hi/Hor if RF1 was connected to Hi/Ver.

4. For each output required, connect an RF cable from an OUT connector

of the signal splitter to the LNB or ANT connector of the individual IRD

units.

5. Terminate any unused connections with a suitable 75 Ohm DC termi-

nator block.

RF1

RF2

POWER/

DATA

Multiswitch

Lo/VerHi/Ver Lo/HorHi/Hor

OUT 3OUT 2

POWER

24V DC

OUT 1 OUT 4

GROUND

Antenna

baseplate

IRD 1 IRD 2

IRD 3 IRD 4

D9280_1

DiSEqC

81258_3.book Page 20 Wednesday, November 8, 2006 2:06 PM

Contents

Main Page Contents Page Safety notices WARNING Product installation In-line fuse Antenna unit cover Page Important information Introduction Geographic location Television reception EMC conformance Declaration of conformity Waste Electrical and Electronic Equipment Directive Restriction of the use of certain Hazardous Substances What does a typical system look like? Satellite receivers, televisions and subscription services must be purchased separately. Page Installation EMC installation guidelines Whats in the box?.... What tools do I need to install my TV system?.... How do I plan the installation?... Cables Power requirements Clear view of sky Extending the cables How do I install the ACU?.... ACU dimensi ons Installing the ACU How do I install the antenna?.... Preparing the antenna Preparing the mount Securing the antenna How do I connect the system cables?.... Connecting the antenna Note: Antenna baseplate Connecting the ACU How do I configure the system?... Systems with 2RF connector baseplate Single IRD In-line fuse Twin IRDs Multiple IRDs North American systems and South America (DirecTV) North American systems - DirecTV Multiswitch MASTER IRD 1 IRD 2 IRD 3 Multi S/W IRD1 Europe, Australia, New Zealand, China, Middle East, South America (Sky) System with 4 RF connector baseplate Single IRD Twin IR Ds Multiple IRDs Systems using up to 4 IRDs Systems using more than 4 IRDs Connecting your satellite TV system to an NMEA0183 GPS * This applies to Raymarine 60 STV systems only. Pin 1 Pin 2 Page System set up Introduction Set up using the ACU Start up Changing the default satellite * Set up mode Setting the satellite pair Setting the satellite pair - DirecTV Setting the GPS using the ACU If your system is connected to a GPS antenna, the position will be updated in real time. Edit satellite information p Note: (1) (2 ) Vertical and horizontal polarization applies to regions with linear polarization only. Setting the local frequency LNB systems in regions with circular polarization Raymarine does not recommend changing the LNB type unless instructed to do so. LNB systems in regions with linear polarization Raymarine does not recommend changing the LNB type unl ess instructed to do so. Setting the DiSEqC method Setting the LNB skew angle This menu is only applicable to Raymarine 60STV Premium models * CALIBRATION - uses the skew sensor motor to position th e LNB. MANUAL- enables you to set the skew angle manually according to signal strength. Display version Setting antenna go position Setting antenna move step Setting defaults Set up using the Graphical User Interface PC GUI main menu Controller menu Antenna status Serial port set up The GUI control soft keys Setting the GPS Editing the satellite information Setting antenna angle, move step and diagnosis. Moving the antenna to a new position Antenna diagnosis Setting the skew angle This section is only applicable to regions with linear polarization. Maintenance and troubleshooting Introduction Maintenance Troubleshooting * for an explanation of possible causes and their remedies refer to the following paragraphs. Page Antenna diagnosis Press EXIT to return to main set up menu. If failed, check the power and data cable connections. Technical support www.raymarine.com Satellite information Introduction Satellite coverage areas Climatic conditions European satellites Page Page Page US satellites Page Australia Optus C1 New Zealand Optus B1 Page Middle East Page South America Satellite coverage by geographic location Europe Page Satellite tracking Satellite service providers European satellites Page North American satellites Australia and New Zealand Far East Page Appendix 7: Technical specification Raymarine 45 STV Page Page Raymarine 60 STV