Raymarine Satellite TV Systems System set up

25

System set up

Introduction

This section of the handbook describes how to set up your Raymarine

Satellite TV system after installation using the ACU or the Graphical User

Interface (GUI) and includes the following functions:

• System start up.

• Change the default satellite.

• Monitor the antenna status.

• Enter set up mode.

• Setting the satellite pair.

• Setting the GPS.

• Setting the local frequency.

• Setting the DiSEqC method.

• Display versions.

• Setting antenna go position.

• Setting antenna move step.

• Setting the default satellites.

Many of the above functions will only be required at initial installation of

your system.

Note:

The satellite names shown on the ACU screen in the fol lowing

illustrations may differ from those on your ACU depending on your

geographic location.

Set up using the ACU

Start up

With the system installed and power applied, the ACU screen will show the

following sequence:

1. Communication is being estab-

lished between the antenna and the

ACU

2. The antenna is initialized.

3. The antenna is searching for Satel-

lite A.

4. The antenna has located the satel-

lite and is now tracking

D7964_1

INITIALIZE ACU

RAYMARINE 45STV

D7965_1

INITIALIZE ANTENNA

RAYMARINE 45STV

D7966_1

SEARCHING A: ASTRA2

B: HOTBIRD SETUP

D7967_1

TRACKING A: ASTRA2

B: HOTBIRD SETUP

81258_3.book Page 25 Wednesday, November 8, 2006 2:06 PM

Contents

Main Page Contents Page Safety notices WARNING Product installation In-line fuse Antenna unit cover Page Important information Introduction Geographic location Television reception EMC conformance Declaration of conformity Waste Electrical and Electronic Equipment Directive Restriction of the use of certain Hazardous Substances What does a typical system look like? Satellite receivers, televisions and subscription services must be purchased separately. Page Installation EMC installation guidelines Whats in the box?.... What tools do I need to install my TV system?.... How do I plan the installation?... Cables Power requirements Clear view of sky Extending the cables How do I install the ACU?.... ACU dimensi ons Installing the ACU How do I install the antenna?.... Preparing the antenna Preparing the mount Securing the antenna How do I connect the system cables?.... Connecting the antenna Note: Antenna baseplate Connecting the ACU How do I configure the system?... Systems with 2RF connector baseplate Single IRD In-line fuse Twin IRDs Multiple IRDs North American systems and South America (DirecTV) North American systems - DirecTV Multiswitch MASTER IRD 1 IRD 2 IRD 3 Multi S/W IRD1 Europe, Australia, New Zealand, China, Middle East, South America (Sky) System with 4 RF connector baseplate Single IRD Twin IR Ds Multiple IRDs Systems using up to 4 IRDs Systems using more than 4 IRDs Connecting your satellite TV system to an NMEA0183 GPS * This applies to Raymarine 60 STV systems only. Pin 1 Pin 2 Page System set up Introduction Set up using the ACU Start up Changing the default satellite * Set up mode Setting the satellite pair Setting the satellite pair - DirecTV Setting the GPS using the ACU If your system is connected to a GPS antenna, the position will be updated in real time. Edit satellite information p Note: (1) (2 ) Vertical and horizontal polarization applies to regions with linear polarization only. Setting the local frequency LNB systems in regions with circular polarization Raymarine does not recommend changing the LNB type unless instructed to do so. LNB systems in regions with linear polarization Raymarine does not recommend changing the LNB type unl ess instructed to do so. Setting the DiSEqC method Setting the LNB skew angle This menu is only applicable to Raymarine 60STV Premium models * CALIBRATION - uses the skew sensor motor to position th e LNB. MANUAL- enables you to set the skew angle manually according to signal strength. Display version Setting antenna go position Setting antenna move step Setting defaults Set up using the Graphical User Interface PC GUI main menu Controller menu Antenna status Serial port set up The GUI control soft keys Setting the GPS Editing the satellite information Setting antenna angle, move step and diagnosis. Moving the antenna to a new position Antenna diagnosis Setting the skew angle This section is only applicable to regions with linear polarization. Maintenance and troubleshooting Introduction Maintenance Troubleshooting * for an explanation of possible causes and their remedies refer to the following paragraphs. Page Antenna diagnosis Press EXIT to return to main set up menu. If failed, check the power and data cable connections. Technical support www.raymarine.com Satellite information Introduction Satellite coverage areas Climatic conditions European satellites Page Page Page US satellites Page Australia Optus C1 New Zealand Optus B1 Page Middle East Page South America Satellite coverage by geographic location Europe Page Satellite tracking Satellite service providers European satellites Page North American satellites Australia and New Zealand Far East Page Appendix 7: Technical specification Raymarine 45 STV Page Page Raymarine 60 STV